* Infinite calibration loop fix
* Save calibration
* Screen refresh
* reduce repeated code
* reduce repeated code to reduce flash
* fix Waypoint compass size and no fix no heading labels
* Don't show compass unless we have a heading and location
* If no calculated heading from moving, we should have no heading
* Slow walking calculated heading and auto stale heading when not moving
* Triming flash space
* cleanup
* show "?" when no location or heading for distance and heading screen
* cleanup
* Stale heading logic
* final trim
* Compass Calibration screen redesign
* Trunk Fix
* Compile fix
* patch
* Update src/motion/MotionSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update WaypointModule.cpp
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Implementation of Status Message
* Change drawNodeInfo to drawFavoriteNode
* Truncate overflow on Favorite frame
* Set MAX_RECENT_STATUSMESSAGES to 5 to meet memory usage targets
The linker script was created by merging variants/STM32WLxx/WL54JCI_WL55JCI_WLE4J(8-B-C)I_WLE5J(8-B-C)I/ldscript.ld and system/ldscript.ld from stm32duino/Arduino_Core_STM32.
mallinfo().fordblks counts only free bytes within the committed arena.
On STM32WL (newlib sbrk heap) the arena grows lazily from _end toward SP,
so fordblks reads near-zero at early boot even when ~48 KB of addressable
space remains. This caused NodeDB::isFull() to fire prematurely and evict
nodes on a freshly booted device.
Fix getFreeHeap() to include uncommitted sbrk headroom (SP - sbrk(0)) so
the returned value reflects true available memory throughout the boot
lifecycle.
Introduce MESHTASTIC_DYNAMIC_SBRK_HEAP as an opt-in build flag (set in
stm32.ini) so the fix is gated to platforms with a dynamic sbrk heap
rather than a static heap. Future platforms with the same heap model can
opt in by adding this flag.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Integrate STM32 battery monitoring into AnalogBatteryLevel, supporting
external GPIO ADC pins as well as internal VBAT channel.
Features:
- ADC reading using STM32 LL (Lower Layer) macros supporting external
ADC channels and internal VBAT channel (AVBAT)
- ADC compensation using STM32 LL macros with factory-calibrated VREFINT
(AVREF) for accurate voltage measurement
- LFP battery OCV curve for STM32WL using AVBAT (STM32 VDD absolute
maximum supply voltage 3.9V, direct connection of Li-Po batteries is
not supported)
Internal VBAT channel implemented in:
- Russell
- RAK3172
In these variants, ADC_MULTIPLIER = (1.01f * 3) = 3.30 as there is a
3:1 internal divider (DS13105 Rev 12 §5.3.21), and a bit of tolerance
as the actual 10% spec leads to readings much too high.
Assisted-by: Claude:sonnet-4-5
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Fix heap blowout on TBeams
* Update src/graphics/draw/MessageRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Set MESSAGE_HISTORY_LIMIT to 10 for original ESP32 to optimize RAM usage
* Optimize message frame allocation to prevent excessive memory usage
* Refine message history limits for resource-constrained builds and cap cached lines to prevent heap overflow
* Update src/graphics/draw/MessageRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix heap blowout on TBeams
* Update src/graphics/draw/MessageRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Set MESSAGE_HISTORY_LIMIT to 10 for original ESP32 to optimize RAM usage
* Optimize message frame allocation to prevent excessive memory usage
* Refine message history limits for resource-constrained builds and cap cached lines to prevent heap overflow
* Update src/graphics/draw/MessageRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* fix(native): implement BinarySemaphorePosix with proper pthread synchronization
The BinarySemaphorePosix class (used on all Linux/portduino/native builds)
had stub implementations: give() was a no-op and take() just called
delay(msec) and returned false. This broke the cooperative thread scheduler
on native platforms — threads could not wake the main loop, radio RX
interrupts were missed, and telemetry never transmitted over the mesh.
Replace the stubs with a proper binary semaphore using pthread_mutex_t +
pthread_cond_t + bool signaled:
- take(msec): pthread_cond_timedwait with CLOCK_REALTIME timeout, consumes
signal atomically (binary semaphore semantics)
- give(): sets signaled=true, signals condition variable
- giveFromISR(): delegates to give(), sets pxHigherPriorityTaskWoken
Tested on Raspberry Pi 3 Model B (ARM64, Debian Bookworm) with Adafruit
LoRa Radio Bonnet (SX1276). Before fix: no radio TX/RX, no telemetry on
mesh. After fix: bidirectional LoRa, MQTT gateway, telemetry all working.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* ARCH_PORTDUINO
* Refactor BinarySemaphorePosix header for ARCH_PORTDUINO
* Change preprocessor directive from ifndef to ifdef
* Gate new Semaphore code to Portduino and fix STM compilation
* Binary Semaphore Posix better error handling
---------
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* fix(native): implement BinarySemaphorePosix with proper pthread synchronization
The BinarySemaphorePosix class (used on all Linux/portduino/native builds)
had stub implementations: give() was a no-op and take() just called
delay(msec) and returned false. This broke the cooperative thread scheduler
on native platforms — threads could not wake the main loop, radio RX
interrupts were missed, and telemetry never transmitted over the mesh.
Replace the stubs with a proper binary semaphore using pthread_mutex_t +
pthread_cond_t + bool signaled:
- take(msec): pthread_cond_timedwait with CLOCK_REALTIME timeout, consumes
signal atomically (binary semaphore semantics)
- give(): sets signaled=true, signals condition variable
- giveFromISR(): delegates to give(), sets pxHigherPriorityTaskWoken
Tested on Raspberry Pi 3 Model B (ARM64, Debian Bookworm) with Adafruit
LoRa Radio Bonnet (SX1276). Before fix: no radio TX/RX, no telemetry on
mesh. After fix: bidirectional LoRa, MQTT gateway, telemetry all working.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* ARCH_PORTDUINO
* Refactor BinarySemaphorePosix header for ARCH_PORTDUINO
* Change preprocessor directive from ifndef to ifdef
* Gate new Semaphore code to Portduino and fix STM compilation
* Binary Semaphore Posix better error handling
---------
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Add powerlimits to reconfigured radio settings as well as init settings.
* Refactor preamble length handling for wide LoRa configurations
* Moved the preamble setting to the main class and made the references static
MQTT password was logged in cleartext via LOG_INFO when connecting to
the broker, exposing credentials to anyone with log access. Replace
the password format specifier with a static mask.
Co-authored-by: Patrickschell609 <patrickschell609@users.noreply.github.com>
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
* Consolidate SHTs into one class
* Remove separate SHT imports
* Create one single SHTXX sensor type
* Let the SHTXXSensor class handle variant detection
* Minor logging improvements
* Add functions to set accuracy on SHT3X and SHT4X
* Fix variable init in constructor
* Add bus to SHT sensor init
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix accuracy conditions on SHTXX
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Merge upstream
* Add SHT2X detection on 0x40
* Read second part of SHT2X serial number
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
SerialModule's weather station parser divides by velCount and dirCount
to compute wind speed/direction averages. Both counters are only
incremented when their respective sensor readings arrive, but the
division runs whenever gotwind is true (set by EITHER reading) and
the averaging interval has elapsed.
If only WindDir arrives without WindSpeed (or vice versa), or if the
timer fires before any readings accumulate, the division produces
undefined behavior (floating-point divide by zero on embedded = NaN
or hardware fault depending on platform).
Fix: add velCount > 0 && dirCount > 0 guard to the averaging block.
Co-authored-by: Patrickschell609 <patrickschell609@users.noreply.github.com>
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
