* stm32wl: check HAL_FLASH_Unlock() return in _internal_flash_erase
_internal_flash_prog already checks HAL_FLASH_Unlock() and returns
LFS_ERR_IO on failure. _internal_flash_erase discarded the return
value, proceeding to erase even if the flash was not unlocked.
Apply the same check for consistency and safety.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* stm32wl: fix _internal_flash_prog to abort on first write error
Previously the programming loop continued to the next doubleword after
HAL_FLASH_Program() failed, potentially writing to invalid addresses
and returning a misleading error code only at the end (last iteration).
HAL_FLASH_Lock() was also skipped on the mid-loop early return path.
- Move bounds check before the loop (validate full range at once)
- Break on first HAL error so subsequent doublewords are not written
- Move HAL_FLASH_Lock() after the loop so it always runs
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* stm32wl: clear stale flash SR error flags before erase and program
Stale error flags in FLASH->SR from a previous failed operation can
cause HAL_FLASH_Program() or HAL_FLASHEx_Erase() to return HAL_ERROR
immediately without attempting the operation.
Add __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_ALL_ERRORS) after each
HAL_FLASH_Unlock() in both _internal_flash_prog and
_internal_flash_erase to ensure a clean state before each operation.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* stm32wl: reject flash prog writes not aligned to 8-byte doubleword
The STM32WL HAL minimum write unit is one 64-bit doubleword (8 bytes).
_internal_flash_prog silently truncated any trailing bytes when size % 8
!= 0 because dw_count = size / 8 drops the remainder. Return LFS_ERR_INVAL
early so LittleFS sees the error rather than a silent short write.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(nrf52,fs): use atomic SafeFile rename instead of direct write
NRF52 was bypassing the .tmp/readback/rename path entirely — openFile()
deleted the target file and wrote directly to it, and close() returned
true without verifying the write or renaming anything.
Adafruit_LittleFS::rename() calls lfs_rename() directly (confirmed at
Adafruit_LittleFS.cpp:205). Remove both ARCH_NRF52 guards so NRF52
follows the same write-to-.tmp → readback-hash → rename path used by
all other platforms.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(admin): skip uiconfig.proto save on devices without a screen
handleStoreDeviceUIConfig() was writing /prefs/uiconfig.proto
unconditionally. MenuHandler.cpp is already gated behind #if HAS_SCREEN,
so there is no path that populates UI config on screen-less platforms.
Guard the save with #if HAS_SCREEN to avoid wasting a flash block on
devices that will never use it.
The read path (handleGetDeviceUIConfig) does not touch the filesystem
and needs no change.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* fs: enable format-on-retry for all platforms in saveToDisk
The FSCom.format() call on save failure was guarded to ARCH_NRF52 with
a comment that other platforms were not ready (bug #4184). STM32WL was
added to the guard in a prior commit. All platforms now expose format
semantics and the retry logic is identical — remove the guard.
To keep NodeDB.cpp platform-agnostic and fix a CI failure on native-tft
(portduino's fs::FS has no format() method), introduce fsFormat() in
FSCommon as the single call-site for all callers:
- Embedded (ESP32, NRF52, STM32WL, RP2040): delegates to FSCom.format()
- Portduino: rmDir("/prefs") + FSBegin() (a no-op on portduino).
rmDir("/prefs") is already called unconditionally by factoryReset()
(NodeDB.cpp:504), so both primitives are proven on portduino.
Replace both direct FSCom.format() calls in NodeDB.cpp with fsFormat().
Note: we do not run portduino locally — portduino/native build testers
please verify the format-on-retry path.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* DO NOT MERGE: nrf52(fs): add File() default constructor bound to InternalFS
Adds File() to the Adafruit LittleFS File class (in the Meshtastic
Adafruit_nRF52_Arduino fork), delegating to File(InternalFS). This
matches the default-constructible File API on all other platforms.
The constructor is implemented in Adafruit_LittleFS_File.cpp rather
than inline in the header to avoid a circular include between
Adafruit_LittleFS_File.h and InternalFileSystem.h.
FOLLOW-UP REQUIRED: nrf52.ini points to a commit SHA on the
mesh-malaysia/Adafruit_nRF52_Arduino fork instead of the upstream
meshtastic framework. Once meshtastic/Adafruit_nRF52_Arduino#5 is
merged, revert nrf52.ini to point back to the upstream meshtastic
framework URL.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* stm32wl(fs): add File() default constructor and document LFS tunables
Adds File() to STM32_LittleFS_Namespace::File, delegating to
File(InternalFS). Implemented in the .cpp to avoid a circular include
between STM32_LittleFS_File.h (which cannot include LittleFS.h) and
the InternalFS extern declaration.
This matches the File API on ESP32/RP2040/Portduino and is a
prerequisite for removing the ARCH_STM32WL guard in xmodem.h.
No behavior change — the constructor leaves the file in the same
closed/unattached state as File(InternalFS) would.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* fs: remove arch-specific ifdefs from FSCommon, SafeFile, xmodem
Now that NRF52 and STM32WL have File() default constructors and NRF52
has working atomic SafeFile rename, the capability gaps are closed.
Remove all per-arch guards across the shared FS layer:
FSCommon.cpp — renameFile():
Use FSCom.rename() on all platforms. Adafruit_LittleFS::rename()
calls lfs_rename() directly (Adafruit_LittleFS.cpp:205). The
copy+delete fallback on NRF52/RP2040 was never necessary.
FSCommon.cpp — getFiles():
Replace four ARCH_ESP32 guards with a single filepath pointer at
the top of the loop (file.path() on ESP32, file.name() elsewhere).
Fix strcpy(fileInfo.file_name, filepath): bounded to
sizeof(fileInfo.file_name)-1 with explicit NUL termination to prevent
overflow of the 228-byte meshtastic_FileInfo::file_name array.
FSCommon.cpp — listDir():
Same filepath pointer approach. NRF52/STM32WL were in an else-branch
that only logged but never deleted — now all platforms follow the
unified del path. 12 guards → 2.
Fix three strncpy(buffer, ..., sizeof(buffer)) calls that did not
NUL-terminate when source length >= sizeof(buffer) (255 bytes).
Add explicit buffer[sizeof(buffer)-1] = '\0' after each.
FSCommon.cpp — rmDir():
Use listDir(del=true) everywhere. The ARCH_NRF52 rmdir_r() path and
the ARCH_ESP32|RP2040|PORTDUINO listDir() path collapse to one line.
SafeFile.cpp:
ARCH_NRF52 bypass removed (handled in preceding commit).
xmodem.h:
File file; now works on all platforms via default constructors
added in the two preceding commits.
Remaining #ifdef ARCH_ESP32 in FSCommon.cpp: exactly 4, all for the
file.path() vs file.name() API difference (ESP32 Arduino LittleFS
returns the full path; all others return only the name). That
difference lives in the framework and cannot be closed here.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* stm32wl(fs): add write-behind page cache, reduce virtual block size and FS reservation (FORMAT BREAK)
Adds a write-behind (RMW) page cache to the STM32WL LittleFS driver,
modelled after the NRF52 Adafruit approach (flash_cache.c). This allows
LFS to use 256-byte virtual blocks backed by 2048-byte physical pages:
the erase/prog callbacks accumulate changes in a 2 KB RAM buffer; the
sync callback (and page eviction on page-change) flushes with a single
HAL physical-erase + doubleword-program pass.
LFS tunables changed (FORMAT BREAK — superblock parameters):
block_size: 2048 B → 256 B (8 virtual blocks per physical page)
read_size: 2048 B → 256 B (= block_size)
prog_size: 2048 B → 256 B (= block_size; hardware min is 8 B)
block_count: 112 → 80 (14 phys pages → 10 phys pages = 20 KiB)
Benefits:
- Internal fragmentation: max 2047 B/file → max 255 B/file
- Heap per open LFS file: ~4 KB → 512 B (prog + read buffers)
- Code flash headroom: 6.7 KB → ~14.1 KB (+7.4 KB)
- Block budget: 80 virtual blocks, worst-case peak ~20, ~60 free
Updates board_upload.maximum_size in wio-e5/platformio.ini from 233472
(256 KB − 28 KB) to 241664 (256 KB − 20 KB) to match the reduced FS
reservation.
Justification for the format break: the prior STM32WL firmware had
several flash write bugs fixed earlier in this series (missing error
flag clearing, no abort on first write failure, unaligned write
acceptance). These bugs very likely caused silent config corruption on
deployed devices. The format break should be treated as an enhancement:
it provides a clean, reliably-written starting point. Users will need
to reconfigure their device once after this update.
Correctness fixes applied to the cache implementation:
- alignas(8) on _page_cache: the buffer was uint8_t[] (alignment 1)
but _flash_cache_flush casts it to const uint64_t* — undefined
behaviour per C++ standard, potential Cortex-M hardfault. alignas(8)
guarantees the required alignment for the doubleword cast.
- HAL_FLASH_Lock() return value: was discarded. Now assigned to
lock_rc and propagated into rc if prior writes succeeded, so LFS
sees the error rather than a false success.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* stm32wl(fs): reduce FS reservation from 10 pages to 7 pages (FORMAT BREAK)
Reduces LFS_FLASH_TOTAL_SIZE from 10 × 2 KiB pages (20 KiB) to
7 × 2 KiB pages (14 KiB), freeing 6 KiB for firmware.
board_upload.maximum_size updated accordingly across all STM32WL variants:
241664 (256 KiB - 20 KiB) → 247808 (256 KiB - 14 KiB)
This is a FORMAT BREAK: existing filesystems must be erased before use.
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
* fix(fs): return false in renameFile() when FSCom is not defined
Avoids undefined behavior and -Wreturn-type warnings in configurations
that compile FSCommon.cpp without a filesystem backend.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix: apply all LoRa config changes live without rebooting
All LoRa radio settings (SF, BW, CR, frequency, power, preset,
sx126x_rx_boosted_gain) now apply immediately via reconfigure()
without requiring a node reboot.
- AdminModule: requiresReboot = false for all LoRa config changes;
LoRa changes were already handled by the configChanged observer
calling reconfigure() but the reboot flag was set unnecessarily
- AdminModule: validate LORA_24 region against radio hardware at
config time; reject with BAD_REQUEST if hardware lacks 2.4 GHz
capability (wideLora() returns false or no radio instance)
- SX126xInterface/LR11x0Interface: apply sx126x_rx_boosted_gain in
reconfigure(); register 0x08AC is writable in STDBY mode (SX1261/2
datasheet §9.6); retention registers written so setting survives
warm-sleep cycles; log warning on setter failure
- DebugRenderer: show BW/SF/CR on debug screen when custom modem is
active instead of the preset name
- DisplayFormatters: clarify comment on getModemPresetDisplayName
* fix: remove redundant reboot after LoRa config changes in on-device menus
Region, frequency slot, and radio preset pickers in MenuHandler all
called reloadConfig() then immediately set rebootAtMsec. reloadConfig()
already fires the configChanged observer which calls reconfigure(), so
the forced reboot was unnecessary — same rationale as the parent commit.
* fix: guard LORA_24 region selection against hardware capability in on-device menu
Without a reboot, reconfigure() now applies region changes directly.
Previously getRadio() caught the LORA_24-on-sub-GHz mismatch post-reboot
and reverted to UNSET — that safety net is gone. Add an explicit wideLora()
check in LoraRegionPicker so sub-GHz-only hardware silently ignores LORA_24
selection instead of attempting a live reconfigure with an invalid frequency.
---------
Co-authored-by: elwimen <elwimen@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Enhance LoRa configuration with modem presets and validation logic
* Rename bootstrapLoRaConfigFromPreset tests to validateModemConfig for clarity and consistency
* additional tidy-ups to the validateModemConfig - still fundamentally broken at this point
* Enhance region validation by adding numPresets to RegionInfo and implementing validateRegionConfig in RadioInterface
* Add validation for modem configuration in applyModemConfig
* Fix region unset handling and improve modem config validation in handleSetConfig
* Refactor LoRa configuration validation methods and introduce clamping method for invalid settings
* Update handleSetConfig to use fromOthers parameter to either correct or reject invalid settings
* Fix some of the copilot review comments for LoRa configuration validation and clamping methods; add tests for region and preset handling
* Redid the slot default checking and calculation. Should resolve the outstanding comments.
* Add bandwidth calculation for LoRa modem preset fallback in clampConfigLora
* Remove unused preset name variable in validateConfigLora and fix default frequency slot check in applyModemConfig
* update tests for region handling
* Got the synthetic colleague to add mock service for testing
* Flash savings... hopefully
* Refactor modem preset handling to use sentinel values and improve default preset retrieval
* Refactor region handling to use profile structures for modem presets and channel calculations
* added comments for clarity on parameters
* Add shadow table tests and validateConfigLora enhancements for region presets
* Add isFromUs tests for preset validation in AdminModule
* Respond to copilot github review
* address copilot comments
* address null poointers
* fix build errors
* Fix the fix, undo the silly suggestions from synthetic reviewer.
* we all float here
* Fix include path for AdminModule in test_main.cpp
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* More suggestion fixes
* admin module merge conflicts
* admin module fixes from merge hell
* fix: initialize default frequency slot and custom channel name; update LNA mode handling
* save some bytes...
* fix: simplify error logging for bandwidth checks in LoRa configuration
* Update src/mesh/MeshRadio.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Add ESP32 Power Management lessons learned document
Documents our experimentation with ESP-IDF DFS and why it doesn't
work well for Meshtastic (RTOS locks, BLE locks, USB issues).
Proposes simpler alternative: manual setCpuFrequencyMhz() control
with explicit triggers for when to go fast vs slow.
* Addition of traffic management module
* Fixing compile issues, but may still need to update protobufs.
* Fixing log2Floor in cuckoo hash function
* Adding support for traffic management in PhoneAPI.
* Making router_preserve_hops work without checking if the previous hop was a router. Also works for CLIENT_BASE.
* Adding station-g2 and portduino varients to be able to use this module.
* Spoofing from address for nodeinfo cache
* Changing name and behavior for zero_hop_telemetry / zero_hop_position
* Name change for exhausting telemetry packets and setting hop_limit to 1 so it will be 0 when sent.
* Updated hop logic, including exhaustRequested flag to bypass some checks later in the code.
* Reducing memory on nrf52 nodes further to 12 bytes per entry, 12KB total using 8 bit hashes with 0.4% collision. Probably ok. Adding portduino to the platforms that don't need to worry about memory as much.
* Fixing hopsAway for nodeinfo responses.
* traffic_management.nodeinfo_direct_response_min_hops -> traffic_management.nodeinfo_direct_response_max_hops
* Removing dry run mode
* Updates to UnifiedCacheEntry to use a common cache, created defaults for some values, reduced a couple bytes per entry by using a resolution-scale time selection based on configuration value.
* Enhance traffic management logging and configuration. Updated log messages in NextHopRouter and Router to include more context. Adjusted traffic management configuration checks in AdminModule and improved cache handling in TrafficManagementModule. Ensured consistent enabling of traffic management across various variants.
* Implement destructor for TrafficManagementModule and improve cache allocation handling. The destructor ensures proper deallocation of cache memory based on its allocation source (PSRAM or heap). Additionally, updated cache allocation logic to log warnings only when PSRAM allocation fails.
* Update TrafficManagementModule with enhanced comments for clarity and improve cache handling logic. Update protobuf submodule to latest commit.
* Creating consistent log messages
* Remove docs/ESP32_Power_Management.md from traffic_module
* Add unit tests for Traffic Management Module functionality
* Fixing compile issues, but may still need to update protobufs.
* Adding support for traffic management in PhoneAPI.
* Making router_preserve_hops work without checking if the previous hop was a router. Also works for CLIENT_BASE.
* Enhance traffic management logging and configuration. Updated log messages in NextHopRouter and Router to include more context. Adjusted traffic management configuration checks in AdminModule and improved cache handling in TrafficManagementModule. Ensured consistent enabling of traffic management across various variants.
* Implement destructor for TrafficManagementModule and improve cache allocation handling. The destructor ensures proper deallocation of cache memory based on its allocation source (PSRAM or heap). Additionally, updated cache allocation logic to log warnings only when PSRAM allocation fails.
* Update TrafficManagementModule with enhanced comments for clarity and improve cache handling logic. Update protobuf submodule to latest commit.
* Add mock classes and unit tests for Traffic Management Module functionality.
* Refactor setup and loop functions in test_main.cpp to include extern "C" linkage
* Update comment to include reduced memory requirements
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Re-arranging comments for programmers with the attention span of less than 5 lines of code.
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update comments in TrafficManagementModule to reflect changes in timestamp epoch handling and memory optimization details.
* bug: Use node-wide config_ok_to_mqtt setting for cached NodeInfo replies.
* Better way to handle clearing the ok_to_mqtt bit
* Add bucketing to cuckoo hashing, allowing for 95% occupied rate before major eviction problems.
* Extend nodeinfo cache for psram devices.
* Refactor traffic management to make hop exhaustion packet-scoped. Nice catch.
* Implement better position precision sanitization in TrafficManagementModule.
* Added logic in TrafficManagementModule to invalidate stale traffic state. Also, added some tests to avoid future me from creating a regression here.
* Fixing tests for native
* Enhance TrafficManagementModule to improve NodeInfo response handling and position deduplication logic. Added tests to ensure local packets bypass transit filters and that NodeInfo requests correctly update the requester information in the cache. Updated deduplication checks to prevent dropping valid position packets under certain conditions.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Adds ROUTER_LATE and CLIENT_BASE to preferred rebroadcaster check
(skip unsolicited NodeInfo) and prevents ROUTER_LATE from setting
rebroadcast mode to NONE, which would silently break relaying.
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
* Partition header check for OTA type
* Guards
* Guards
* Derp
* Missed one
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
* Regen protobufs
* Ensure mute state is set when node is ignored
* Added mechanism for toggling muted state
* Implement the ability to mute specific nodes
* Switch boolean value for bitmask
* Correctly toggle bitfield position 2 on-change to mute state
* Dont push submodule refs
* Log correct info
* Trunk fmt
* Update protobuf ref to master branch of base
* Update src/modules/ExternalNotificationModule.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Re-sync generated files
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
* Conditionally delete favourited nodes on reset
* trunk fmt
* Fix equality check, use existing macro for role validation
* Extend favourite persistence setting to devices of all roles
* Refactor: Decoupled role/config check and set role defaults appropriately
* Use American-English spelling
* Use existing reference
* Convert reset to bool, regen protos
* Add optional arg to nodedb_reset in favor of additional device setting
* Use correct proto commit ID
* Regen protos
* Log preservation status
* Pull latest from master
* Null out user.id except for sending to phone
* Fix
* Update src/modules/NodeInfoModule.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Copilot garbage
* This is unnecessary, because we don't stored user.id on userlite
* Don't need this
* Fix warning
* Just alter the protobuf
* Alter protobuf doesn't do anything with the altered data, so let's re-encode it
* Check inputbroker before access
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix excluded modules configuration handling
- Add excluded_modules flags in getDeviceMetadata() for MQTT, PAXCOUNTER, STOREFORWARD, RANGETEST, NEIGHBORINFO
- Add conditional compilation guards in AdminModule for RANGETEST, AUDIO, PAXCOUNTER, STOREFORWARD, EXTNOTIF, DETECTIONSENSOR, AMBIENTLIGHTING
- Add skip logic in PhoneAPI for excluded modules during config enumeration
- Add conditional has_* flags in NodeDB only for included modules
Fixes issue where excluded modules still appeared in client applications and sometimes caused PAYLOADVARIANT_NOT_SET errors.
* Fix excluded modules issues and refactor code
- Restore original PAXCOUNTER logic: only exclude on non-ESP32 platforms due to memory constraints
- Fix has_store_forward flag to be conditionally compiled based on MESHTASTIC_EXCLUDE_STOREFORWARD
- Refactor PhoneAPI module config skipping logic to use helper function skipExcludedModuleConfig()
- Reduce code duplication in PhoneAPI by extracting common skip logic
This addresses the three issues identified in the code review:
1. PAXCOUNTER memory impact on non-ESP32 devices
2. Unconditional has_store_forward flag setting
3. Duplicated state management logic across multiple #else blocks
* Fix ambient lighting module exclusion in PhoneAPI and AdminModule
- Add conditional compilation guards for ambient lighting in PhoneAPI.cpp
- Replace old HAS_RGB_LED logic with MESHTASTIC_EXCLUDE_AMBIENTLIGHTING check in AdminModule.cpp
- Ensure ambient lighting module is properly excluded when MESHTASTIC_EXCLUDE_AMBIENTLIGHTING=1
* Clear position on GPS deactivation, unless using fixed position
As reported by @dreimal8 , and confirmed by @tuxmobil , when using
and then subsequently disabling GPS the last position retrieved from
the GPS was stored and continued to be broadcast.
This change introduces a check to see if we are transitioning from
GPS Enabled to GPS Disabled or Not Present. If we are, and fixed
position is not in use, then we clear the local position.
This will prevent inaccurate and undesired position broadcasts for those
who disable their GPS.
Fixes https://github.com/meshtastic/firmware/issues/7228
* Update triple click to also clear position
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
