* feat: add Nordic nRF54L15-DK variant (Zephyr + BLE + LoRa)
Adds a community hardware variant for the Nordic nRF54L15-DK (PCA10156)
with an external EBYTE E22-900M30S (SX1262) LoRa module. First Meshtastic
port running on the Zephyr RTOS; all other Nordic targets use the nRF5
SoftDevice stack.
Scope
-----
- New Zephyr-based platform layer under src/platform/nrf54l15/ providing
Arduino-compatible shims (Arduino.h, SPI, Wire, Print, Stream) over the
Zephyr APIs plus a LittleFS-backed InternalFileSystem on SPIM20.
- Bluetooth LE peripheral (NRF54L15Bluetooth.*) built on the Zephyr BT
host stack, exposing the Meshtastic GATT service with legacy
connectable advertising, just-works pairing, dynamic MTU exchange
(up to 247 bytes), and iOS connection-parameter tweaks.
- Variant directory variants/nrf54l15/nrf54l15dk/ with pin map for the
E22 module on connector J1, PlatformIO env (nrf54l15dk), Zephyr
DT overlay and a wiring README.
- Zephyr project config (zephyr/prj.conf + board overlay) tuned for
BT + LoRa: 16 KB main stack, 4 KB BT RX thread, RTT logging in
immediate mode, newlib-nano heap sized to leave room for the GATT
pools while still allowing ATT MTU=247.
- extra_scripts/nrf54l15_linker.py works around a PlatformIO + old Ninja
issue where Zephyr's two-pass linker script generation does not run
automatically; the post-script parses build.ninja and invokes the
gcc -E step directly before the final link.
- boards/nrf54l15dk.json board definition (PlatformIO needs it for the
DK; the Seeed platform only ships the XIAO variants).
- variants/rp2350/rp2350.ini excludes platform/nrf54l15/ from RP2350
build_src_filter so the shared platform tree does not leak between
targets.
- .gitignore: add nRF J-Link / RTT debug artifacts (flash.jlink,
rtt_*.txt).
Shared source changes
---------------------
- src/main.{cpp,h}, src/RedirectablePrint.cpp, src/FSCommon.{cpp,h},
src/mesh/{Channels,NodeDB,RadioLibInterface,MeshService,PhoneAPI}.cpp,
src/mesh/RadioLibInterface.h, src/modules/AdminModule.cpp: add small
guards / helpers so the Zephyr build compiles alongside the Arduino
targets. Behavior on existing boards is unchanged.
Hardware model
--------------
HW_VENDOR maps to meshtastic_HardwareModel_PRIVATE_HW until a dedicated
protobuf enum value is assigned upstream. The variant declares
custom_meshtastic_hw_model = 132 so the maintainers can wire the new
enum value through the protobufs repo after merge.
Hardware note
-------------
The E22-900M30S does not connect its DIO2 pin to TXEN internally — a
wire/solder bridge between DIO2 and TXEN on the module is required for
TX to work. Details and full pin map are in the variant README.
Validation
----------
Built clean against develop. On real hardware (April 2026) the port
passes end-to-end: iOS companion app pairs and connects, configuration
round-trip works, LoRa TX/RX reaches a canonical tbeam on the same mesh
channel, NodeDB updates propagate both ways, and traceroute completes.
* fix(nrf54l15): use atomic fs_rename instead of copy fallback
Zephyr LittleFS on nrf54l15 supports fs_rename natively, so route it
through the same atomic path as ESP32. The previous copyFile+remove
fallback truncated the destination before copying, leaving 0-byte files
if interrupted mid-write.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): expand storage_partition from 36KB to 700KB
LittleFS on the default 9-block (36KB) storage_partition ran out of
space during copy-on-write of config.proto, causing fs_write to return
ENOSPC and pb_encode to surface "io error" when saving configuration
via the mobile app.
Reclaim slot1_partition (the MCUboot secondary slot — unused since we
flash directly via J-Link) and grow storage_partition to span
0xb6000..0x165000 (~175 blocks).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): drop USERPREFS_LORACONFIG_* so LoRa config stays mutable
NodeDB rewrites LoRa config from USERPREFS_LORACONFIG_* on every boot,
which prevented reconfiguration via the BLE/serial app. Drop the
variant-level defaults; users configure region and modem preset through
the app like every other variant.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): enforce MITM passkey pairing on GATT service
- Add MESH_PERM_READ/MESH_PERM_WRITE macros (READ_AUTHEN/WRITE_AUTHEN)
on all mesh service characteristics so clients must complete passkey
exchange before accessing fromNum/fromRadio/toRadio/logRadio.
- Wire FIXED_PIN mode to bt_passkey_set() so the device advertises a
known PIN (config.bluetooth.fixed_pin); RANDOM_PIN keeps default
per-pairing random passkey.
- Reduce BleDeferredThread HARD_WATCHDOG_MS from 3min to 1min.
- prj.conf: CONFIG_BT_SMP_ENFORCE_MITM=y, CONFIG_BT_FIXED_PASSKEY=y,
CONFIG_BT_SMP_SC_PAIR_ONLY=n (legacy fallback for clients that abort
SC pairing with reason 0x01 within 150ms).
* fix(nrf54l15): resolve develop-merge conflict + cppcheck warnings
The `Merge branch 'develop'` left two ~RadioLibInterface() declarations
in src/mesh/RadioLibInterface.h: the inline version added upstream by
PR #10254 (which independently applied the same UAF guard this PR was
carrying) and the out-of-line version this PR introduced. GCC rejects
the duplicate, breaking every platform build. Drop the out-of-line
declaration + definition; keep upstream's inline form.
Also silence the 13 cppcheck low warnings introduced by the new
nrf54l15 Arduino shim — Arduino's `String`/`SPISettings` API contract
relies on implicit single-arg constructors used pervasively by
existing Meshtastic code, so suppress `noExplicitConstructor` inline
with a comment instead of breaking the API. The few mechanical wins
(`const tmp[2]`, `const uint32_t *sp`) are applied directly.
* fmt: fix Trunk Check lint issues on nrf54l15-port
- extra_scripts/nrf54l15_linker.py: move regular imports above
Import("env") to silence E402, add trunk-ignore-all(F821) for the
PIO/SCons SConstruct injection (matches esp32_pre.py / nrf52_extra.py
convention)
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clang-format 16.0.3
- boards/nrf54l15dk.json + variants/nrf54l15/nrf54l15dk/README.md:
prettier 3.8.3 (also resolves markdownlint MD060 on README tables)
No behavior change.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address Copilot review comments + correct clang-format style
Six review threads from the 2026-04-30 Copilot review:
- src/platform/nrf54l15/nrf54l15_main.cpp: validate PSP against the nRF54L15
SRAM range (0x20000000..0x20040000) and 4-byte alignment before walking the
faulting thread's stack, and clamp the walk so it never reads past the end
of RAM. Prevents a second fault inside the fatal handler when PSP is
corrupted (common in real faults).
- src/platform/nrf54l15/nrf54l15_arduino.cpp: gate the bring-up printk traces
in digitalWrite/digitalRead (CS/NRESET toggle log, BUSY-before-NRESET
snapshot, BUSY periodic timeline) behind a new -DNRF54L15_GPIO_DEBUG flag
that is off by default. The "dev NOT READY" message stays unconditional —
it indicates a genuine hardware/DTS misconfig.
- src/modules/AdminModule.cpp: don't mutate config.device.output_gpio_enabled
from handleGetConfig(). Reflect the live pin state in the response payload
only — a getter must not write back to disk-persisted state.
- src/platform/nrf54l15/InternalFileSystem.h: derive totalBytes() from
FIXED_PARTITION_SIZE(storage_partition) at compile time so it tracks the
DK overlay's ~700 KB partition instead of the stale 36 KB hard-coded value.
Updated the file header comment accordingly.
- extra_scripts/nrf54l15_linker.py: make _extract_gcc_command() handle the
POSIX Ninja COMMAND format (no `cmd.exe /C "..."` wrapper) in addition to
the Windows form, so the script doesn't hard-fail on Linux/macOS hosts.
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clamp NO_PIN to RANDOM_PIN
with a one-shot LOG_WARN. The mesh GATT permissions are declared with
BT_GATT_PERM_*_AUTHEN and prj.conf sets CONFIG_BT_SMP_ENFORCE_MITM=y, so
NO_PIN with no auth callbacks would leave every characteristic returning
BT_ATT_ERR_AUTHENTICATION. Falling back to RANDOM_PIN keeps the link
usable instead of silently broken. Also re-formatted this file with the
project's .trunk/configs/.clang-format (Linux braces, 4-space indent,
130-col) — the previous lint-fix commit a2aca3234 accidentally used the
default LLVM style here, which CI's clang-format would have rejected.
Build verified: pio run -e nrf54l15dk passes, RAM 47.4%, Flash 28.6%.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address remaining Copilot review threads
Round 2/3 review fixes — bugs first, then docs/portability:
BLE concurrency (NRF54L15Bluetooth.cpp):
- onNowHasData / sendLog / BleDeferredThread / shutdown: acquire
active_conn under ble_mutex via new acquire_active_conn() helper so
disconnected_cb can't free the conn between the null check and
bt_conn_ref/bt_gatt_notify (use-after-unref).
- write_toradio: reject writes that exceed MAX_TO_FROM_RADIO_SIZE with
ATT_ERR_INVALID_ATTRIBUTE_LEN instead of returning success and silently
dropping the payload (would hide failed config writes from the phone).
- start_advertising: truncate the device name to fit the 31-byte legacy
scan-response limit and switch to BT_DATA_NAME_SHORTENED so
bt_le_adv_start() doesn't reject the payload when the name approaches
CONFIG_BT_DEVICE_NAME_MAX=32.
Linker / portability:
- main.h: drop the rp2040Loop() forward declaration that had no
definition and no callers — would surface as a link error if any RP2040
build added a call to the symbol.
- nrf54l15_arduino.cpp: transfer16() now uses static __aligned(4) DMA
buffers (matching transfer()), removing the EasyDMA-reachability hazard
of caller-stack buffers on this part.
Filesystem (InternalFileSystem.h):
- usedBytes(): return real usage from fs_statvfs() instead of 0 so OTA
/ range-test free-space guards work.
- rewindDirectory(): close the dir before reopening — Zephyr fs_dir_t has
no rewind, and re-fs_opendir on an open handle leaks LittleFS state.
Crash handler (nrf54l15_main.cpp):
- After the stack walk, busy-wait 50 ms to flush RTT/printk and call
sys_reboot(SYS_REBOOT_COLD) directly so the saved_crash record is
actually reported on the next boot. Default Zephyr config has
RESET_ON_FATAL_ERROR=n, so the previous k_fatal_halt() spun forever.
Generalization / config:
- PhoneAPI.cpp: replace the NRF54L15_DK ifdef with a
MESHTASTIC_EXCLUDE_FILES_MANIFEST capability flag (defined in the
nrf54l15dk env) so future variants can opt in/out without touching
shared code.
- variants/nrf54l15/nrf54l15.ini: parameterize libdeps include paths via
${PIOENV} so additional nRF54L15 envs sharing nrf54l15_base don't break.
- prj.conf: drop the stale "36 KB storage_partition" comments — the DK
overlay reclaims slot1 to ~700 KB and runtime size comes from
FIXED_PARTITION_SIZE.
- nrf54l15dk overlay: remove the zephyr,console / zephyr,shell-uart
chosen entries that conflicted with CONFIG_UART_CONSOLE=n + RTT
console; keep uart30 enabled so swapping the console is one Kconfig
flip away.
Build: nrf54l15dk SUCCESS (flash 28.6%, RAM 47.4%); wiznet_5500_evb_pico2
SUCCESS (verifies the shared main.h change).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15dk): use PRIVATE_HW (255) for custom_meshtastic_hw_model
Per @thebentern's review: the nRF54L15-DK is a development kit, not a
canonical Meshtastic SKU, so it falls under HardwareModel::PRIVATE_HW
(255) — the same enum value already used at runtime via HW_VENDOR. The
placeholder 132 is removed; no dedicated enum number will be assigned
for DK boards. Slug stays NRF54L15_DK as a human-readable identifier.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): unstarve bt_long_wq so SC pairing completes
bt_pub_key_gen() runs the ECC P256 key generation on bt_long_wq. At default
prio=10 (preemptible) and stack=1400 it gets starved by Meshtastic app
threads at boot — sc_public_key stays NULL for minutes, smp_public_key()
defers with SMP_FLAG_PKEY_SEND, and every SC pairing attempt stalls right
after the public-key exchange. iOS shows "Connecting…" forever with no
PIN prompt; bleak/CLI fails the first CCC notify write with
"Protocol Error 0x05: Insufficient Authentication".
Set CONFIG_BT_LONG_WQ_PRIO=0 (highest preemptible, ties with main) and
CONFIG_BT_LONG_WQ_STACK_SIZE=4096 (margin for the P256M driver frames).
Validated E2E with iOS Meshtastic app: bt_smp_pkey_ready fires within ~40 s
of boot, 20 SC Passkey Entry rounds complete with matching pcnf/cfm,
encrypt 0x01 / sec_level 0x04 (Authenticated MITM), bonded=1.
* feat(nrf54l15): hardware I2C bus via TWIM30 + sensor telemetry
Adds the Arduino TwoWire layer for the nRF54L15-DK so Meshtastic's
sensor drivers can talk to external I2C devices over the hardware
TWIM30 peripheral.
Bus binding:
- &uart30 disabled in the board overlay (peripheral instance 30 is
shared between UARTE30 / TWIM30 / SPIM30 — pick one). Console stays
on RTT via CONFIG_RTT_CONSOLE.
- New i2c30_default / i2c30_sleep pinctrl with SDA=P0.03 / SCL=P0.04.
External 4.7 kOhm pull-ups required on both lines.
- &i2c30 enabled at I2C_BITRATE_FAST (400 kHz).
- button_3 (SW3, P0.04) deleted from DTS so the pad can be claimed by
i2c30 pinctrl; SW3 is still wired to the pad on the DK, do not press
it during I2C use or it will short SCL to GND.
Arduino layer:
- src/platform/nrf54l15/Wire.cpp resolves the DT node at compile time
via DEVICE_DT_GET(DT_NODELABEL(i2c30)) and dispatches Arduino's
beginTransmission / write / endTransmission / requestFrom to
i2c_write / i2c_write_read / i2c_read. Buffer is sized to 256 bytes
for forward compatibility with the SE050 secure element on the
custom PCB.
- Wire.h drops the prior compile-only stubs and exposes the real
TwoWire surface.
- Arduino.h: BitOrder becomes an enum (not #define) so Adafruit_BusIO's
`typedef BitOrder BusIOBitOrder;` compiles.
Variant + build flags:
- nrf54l15.ini flips HAS_WIRE / HAS_SENSOR / HAS_TELEMETRY from 0 to 1
and cherry-picks the sensor libs Meshtastic needs (BusIO, Sensor,
BMP280, BME280, INA219/226/260/3221, SHT4X). The full
environmental_base group is avoided because it pulls
Adafruit_SSD1306 / Adafruit_GFX which rely on Arduino pin macros the
Zephyr shim does not implement.
- nrf54l15dk variant.h defines PIN_WIRE_SDA / PIN_WIRE_SCL for parity
with the Arduino convention used by other variants. The actual bus
wiring is fixed by the overlay pinctrl above.
Validated 2026-05-14/15 on the DK with BMP280 @ 0x76 (temperature +
barometric pressure) and INA3221 @ 0x42 (rail voltage / current);
EnvironmentTelemetry / PowerTelemetry packets transmit successfully
over LoRa.
Footprint cost on nrf54l15dk: +45 KB flash, +1.7 KB RAM.
* feat(nodedb): honor USERPREFS for environment telemetry on first boot
installDefaultConfig() now respects two new compile-time prefs:
USERPREFS_CONFIG_ENV_TELEM_UPDATE_INTERVAL
USERPREFS_CONFIG_ENVIRONMENT_MEASUREMENT_ENABLED
The mobile apps enforce a 30 min floor on environment_update_interval
in the settings UI, which makes short-interval bring-up testing of new
sensor hardware painful — you have to wait half an hour for the first
LoRa packet to confirm wiring + driver. With these prefs baked into
the variant, the firmware can ship a freshly-flashed device that
broadcasts on a shorter cadence (e.g. 900 s) the moment storage_partition
is empty.
Both prefs are gated on #ifdef so the behavior is unchanged for any
variant that does not opt in. Documented in userPrefs.jsonc with the
existing telemetry-interval pref block.
* fix(nrf54l15): allow multiple bonded BLE peers
CONFIG_BT_MAX_PAIRED defaults to 1, so once the first peer (e.g. an
iOS phone) has paired and bonded, every subsequent pairing attempt
from a different MAC fails inside bt_keys_get_addr() with no free
key slot — the host returns BT_SECURITY_ERR_KEY_DOES_NOT_EXIST and
the second peer never gets past SMP.
Raise the slot count to 4 so the device can simultaneously hold an
iOS phone, a Windows host, a Linux host, and one spare bond. Add
BT_KEYS_OVERWRITE_OLDEST so that once the table fills, the LRU peer
is evicted on the next pairing rather than rejecting the new peer.
This matches the behavior other Meshtastic ports already provide
(nRF52 uses CONFIG_BT_PERIPHERAL_PRIO_CONN with similar semantics).
Discovered while bringing up the Python CLI on Windows alongside
the existing iOS bond.
* fix(nrf54l15): zero-initialize TwoWire buffers + clang-format Wire
cppcheck on every CI target (esp32s3, rp2040, rp2350, nrf52840, ...) was
failing the build with two `uninitMemberVar` warnings on TwoWire's
constructor: `txBuf` and `rxBuf` (256-byte arrays) were not initialized.
Even though the buffers are only read after txLen/rxLen is set, leaving
them uninitialized is a footgun if any future caller bypasses the
len-set step. Use C++11 value-initialization in the member initializer
list — costs ~512 B of memset at boot, gains a clean cppcheck pass and
defensive-against-future-changes semantics.
Also reformat Wire.{cpp,h} with the project's `.trunk/configs/.clang-format`
config so the Trunk Check Runner passes — clang-format moved the
`<errno.h>` include before the Zephyr-namespaced ones in Wire.cpp and
collapsed two inline overloads to single lines in Wire.h.
* fix(AdminModule): remove dead OUTPUT_GPIO_PIN/GpioOutputModule references
OUTPUT_GPIO_PIN is never defined and modules/GpioOutputModule.h doesn't
exist in the codebase; all #ifdef OUTPUT_GPIO_PIN branches were dead code
introduced by the nRF54L15-DK variant commit. Strips the include, the
output_gpio_enabled OFF→ON/ON→OFF transition logic in handleSetConfig(),
and the digitalRead() reflection in handleGetConfig().
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* rename variant and add guard macros
* older G3 operational. M7 next.
* Split out G3 and M7 to different variants. Completely new PCB design. The G3 stays on 'PRIVATE_HW'
* Define button behaviour and use all of the device flash
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: caveman99 <25002+caveman99@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
The T-Deck-Pro V1.1 PR (#9378) had a backwards merge (e7b66281) that pulled
236 commits of master INTO a 1-commit fork branch, then a second merge
(8fd0a7f2) duplicated the entire T_DECK/T_DECK_PRO/T_LORA_PAGER/HACKADAY
peripheral init block in setup(). Also removes a stray
digitalWrite(BLE_LED, LED_STATE_OFF) in the HACKADAY section that was an
artifact of the evil merge at e7b66281.
* Add transmit history for throttling that persists between reboots
* Fix RAK long press detection to prevent phantom shutdowns from floating pins
* Update test/test_transmit_history/test_main.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Test fixes and placeholder for content handler tests
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Implement 'agc' reset for SX126x chip family
There's no actual agc on SX126x chips but you can reset the analog
registers by doing a warm sleep & running calibration.
* Address PR comments & implement for LR11x0 too
* calibrate for configured frequency band
* Gate LR11X0_AGC_RESET
* simplify the observer pattern, since all the called functions are const getters.
* use arduino macro over std: for numerical values and refactor local variables in drawScrollbar()
* oh, so Cppcheck actually complained about const pointers not being const.
* slowly getting out of ifdef hell
* fix inkHUD warnings as well
* last 2 check warnings
* git checks should fail on low defects from now on
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Initial implementation for SFA30Sensor
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Add functional SCD4X
* Fix screen frame for CO2
* Add admin commands to SCD4X class
* Add further admin commands and fixes.
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 0847969201.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Small reordering in PMS class for consistency
* If one sensor fails, AQ telemetry still reports data
* Small formatting fix
* Add SEN5X to AQI in ScanI2C
* SCD4X now part of AQ module with template list
* Fixes difference between idle and sleep
* In LowPower, sleep is disabled
* Requires testing for I2C clock comms for commands
* Remove unnecessary import
* Add co2 to serialized AQ metrics
* Add SFA30 with new sensor template in AQ module
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Fix uninitMemberVars
* Fix import error for SCD4X
* Fix I2CClock logic
* Fix not reclocking back to 700000Hz
* Fix multiple sensors being read simultaneously
* The logic in AQ module is different to the one in EnvironmentTelemetryModule. In Env module, if any sensor fails to getMetrics, no valid flag for the module. This prevents other sensors to report data.
* Fix pending clock change in PMSA003
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Make sure clock is always set to needed value
* Fix returns
* Fix trunk
* Fix on condition in reclock
* Fix trunk
* Final SFA30 class implementation
* Add HCHO to screen and improve logs
* Add metrics to mesh packet serializer
* Minor fixes in logs
* OCD tidy up of logs
* Fix sleep function
* Remove old I2C_CLOCK_SPEED code
---------
Co-authored-by: nikl <nikl174@mailbox.org>
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* ExternalNotification and StatusLED now call AmbientLighting to update RGB LEDs. Add optional heartbeat
* Don't overwrite RGB state if heartbeat is disabled.
* Use the right define
* Remove another .h and make rgb static
* move rgb objects into AmbientLighting class
* Straighten out AmbientLighting Thread object
* Use %f for floats
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 0847969201.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Fix trunk
* Fix on condition in reclock
* Add check on polling interval of sen5x
---------
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Added toggable config and default for largeer screens to enable / hide bubbles on chat messages
* Refactor message bubble rendering logic for improved layout and consistency
* Move osk_found initialization for trackball/encoder devices before module setup to fix missing keyboard for L1
* Utilize current checks for consistency
* Reverted last changes
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
* Partition header check for OTA type
* Guards
* Guards
* Derp
* Missed one
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
* Added support for the new SSD1306 control panel.
* Added QMC6310N inspection to I2C scanner
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Autosave Messages
* fix
* Add logging, code cleanup, and add save on delete.
* We already save as part of delete messages, no need to do it again
* fix spelling errors
* Updating comment
---------
Co-authored-by: Jason P <applewiz@mac.com>
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
