* feat: add Nordic nRF54L15-DK variant (Zephyr + BLE + LoRa)
Adds a community hardware variant for the Nordic nRF54L15-DK (PCA10156)
with an external EBYTE E22-900M30S (SX1262) LoRa module. First Meshtastic
port running on the Zephyr RTOS; all other Nordic targets use the nRF5
SoftDevice stack.
Scope
-----
- New Zephyr-based platform layer under src/platform/nrf54l15/ providing
Arduino-compatible shims (Arduino.h, SPI, Wire, Print, Stream) over the
Zephyr APIs plus a LittleFS-backed InternalFileSystem on SPIM20.
- Bluetooth LE peripheral (NRF54L15Bluetooth.*) built on the Zephyr BT
host stack, exposing the Meshtastic GATT service with legacy
connectable advertising, just-works pairing, dynamic MTU exchange
(up to 247 bytes), and iOS connection-parameter tweaks.
- Variant directory variants/nrf54l15/nrf54l15dk/ with pin map for the
E22 module on connector J1, PlatformIO env (nrf54l15dk), Zephyr
DT overlay and a wiring README.
- Zephyr project config (zephyr/prj.conf + board overlay) tuned for
BT + LoRa: 16 KB main stack, 4 KB BT RX thread, RTT logging in
immediate mode, newlib-nano heap sized to leave room for the GATT
pools while still allowing ATT MTU=247.
- extra_scripts/nrf54l15_linker.py works around a PlatformIO + old Ninja
issue where Zephyr's two-pass linker script generation does not run
automatically; the post-script parses build.ninja and invokes the
gcc -E step directly before the final link.
- boards/nrf54l15dk.json board definition (PlatformIO needs it for the
DK; the Seeed platform only ships the XIAO variants).
- variants/rp2350/rp2350.ini excludes platform/nrf54l15/ from RP2350
build_src_filter so the shared platform tree does not leak between
targets.
- .gitignore: add nRF J-Link / RTT debug artifacts (flash.jlink,
rtt_*.txt).
Shared source changes
---------------------
- src/main.{cpp,h}, src/RedirectablePrint.cpp, src/FSCommon.{cpp,h},
src/mesh/{Channels,NodeDB,RadioLibInterface,MeshService,PhoneAPI}.cpp,
src/mesh/RadioLibInterface.h, src/modules/AdminModule.cpp: add small
guards / helpers so the Zephyr build compiles alongside the Arduino
targets. Behavior on existing boards is unchanged.
Hardware model
--------------
HW_VENDOR maps to meshtastic_HardwareModel_PRIVATE_HW until a dedicated
protobuf enum value is assigned upstream. The variant declares
custom_meshtastic_hw_model = 132 so the maintainers can wire the new
enum value through the protobufs repo after merge.
Hardware note
-------------
The E22-900M30S does not connect its DIO2 pin to TXEN internally — a
wire/solder bridge between DIO2 and TXEN on the module is required for
TX to work. Details and full pin map are in the variant README.
Validation
----------
Built clean against develop. On real hardware (April 2026) the port
passes end-to-end: iOS companion app pairs and connects, configuration
round-trip works, LoRa TX/RX reaches a canonical tbeam on the same mesh
channel, NodeDB updates propagate both ways, and traceroute completes.
* fix(nrf54l15): use atomic fs_rename instead of copy fallback
Zephyr LittleFS on nrf54l15 supports fs_rename natively, so route it
through the same atomic path as ESP32. The previous copyFile+remove
fallback truncated the destination before copying, leaving 0-byte files
if interrupted mid-write.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): expand storage_partition from 36KB to 700KB
LittleFS on the default 9-block (36KB) storage_partition ran out of
space during copy-on-write of config.proto, causing fs_write to return
ENOSPC and pb_encode to surface "io error" when saving configuration
via the mobile app.
Reclaim slot1_partition (the MCUboot secondary slot — unused since we
flash directly via J-Link) and grow storage_partition to span
0xb6000..0x165000 (~175 blocks).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): drop USERPREFS_LORACONFIG_* so LoRa config stays mutable
NodeDB rewrites LoRa config from USERPREFS_LORACONFIG_* on every boot,
which prevented reconfiguration via the BLE/serial app. Drop the
variant-level defaults; users configure region and modem preset through
the app like every other variant.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): enforce MITM passkey pairing on GATT service
- Add MESH_PERM_READ/MESH_PERM_WRITE macros (READ_AUTHEN/WRITE_AUTHEN)
on all mesh service characteristics so clients must complete passkey
exchange before accessing fromNum/fromRadio/toRadio/logRadio.
- Wire FIXED_PIN mode to bt_passkey_set() so the device advertises a
known PIN (config.bluetooth.fixed_pin); RANDOM_PIN keeps default
per-pairing random passkey.
- Reduce BleDeferredThread HARD_WATCHDOG_MS from 3min to 1min.
- prj.conf: CONFIG_BT_SMP_ENFORCE_MITM=y, CONFIG_BT_FIXED_PASSKEY=y,
CONFIG_BT_SMP_SC_PAIR_ONLY=n (legacy fallback for clients that abort
SC pairing with reason 0x01 within 150ms).
* fix(nrf54l15): resolve develop-merge conflict + cppcheck warnings
The `Merge branch 'develop'` left two ~RadioLibInterface() declarations
in src/mesh/RadioLibInterface.h: the inline version added upstream by
PR #10254 (which independently applied the same UAF guard this PR was
carrying) and the out-of-line version this PR introduced. GCC rejects
the duplicate, breaking every platform build. Drop the out-of-line
declaration + definition; keep upstream's inline form.
Also silence the 13 cppcheck low warnings introduced by the new
nrf54l15 Arduino shim — Arduino's `String`/`SPISettings` API contract
relies on implicit single-arg constructors used pervasively by
existing Meshtastic code, so suppress `noExplicitConstructor` inline
with a comment instead of breaking the API. The few mechanical wins
(`const tmp[2]`, `const uint32_t *sp`) are applied directly.
* fmt: fix Trunk Check lint issues on nrf54l15-port
- extra_scripts/nrf54l15_linker.py: move regular imports above
Import("env") to silence E402, add trunk-ignore-all(F821) for the
PIO/SCons SConstruct injection (matches esp32_pre.py / nrf52_extra.py
convention)
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clang-format 16.0.3
- boards/nrf54l15dk.json + variants/nrf54l15/nrf54l15dk/README.md:
prettier 3.8.3 (also resolves markdownlint MD060 on README tables)
No behavior change.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address Copilot review comments + correct clang-format style
Six review threads from the 2026-04-30 Copilot review:
- src/platform/nrf54l15/nrf54l15_main.cpp: validate PSP against the nRF54L15
SRAM range (0x20000000..0x20040000) and 4-byte alignment before walking the
faulting thread's stack, and clamp the walk so it never reads past the end
of RAM. Prevents a second fault inside the fatal handler when PSP is
corrupted (common in real faults).
- src/platform/nrf54l15/nrf54l15_arduino.cpp: gate the bring-up printk traces
in digitalWrite/digitalRead (CS/NRESET toggle log, BUSY-before-NRESET
snapshot, BUSY periodic timeline) behind a new -DNRF54L15_GPIO_DEBUG flag
that is off by default. The "dev NOT READY" message stays unconditional —
it indicates a genuine hardware/DTS misconfig.
- src/modules/AdminModule.cpp: don't mutate config.device.output_gpio_enabled
from handleGetConfig(). Reflect the live pin state in the response payload
only — a getter must not write back to disk-persisted state.
- src/platform/nrf54l15/InternalFileSystem.h: derive totalBytes() from
FIXED_PARTITION_SIZE(storage_partition) at compile time so it tracks the
DK overlay's ~700 KB partition instead of the stale 36 KB hard-coded value.
Updated the file header comment accordingly.
- extra_scripts/nrf54l15_linker.py: make _extract_gcc_command() handle the
POSIX Ninja COMMAND format (no `cmd.exe /C "..."` wrapper) in addition to
the Windows form, so the script doesn't hard-fail on Linux/macOS hosts.
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clamp NO_PIN to RANDOM_PIN
with a one-shot LOG_WARN. The mesh GATT permissions are declared with
BT_GATT_PERM_*_AUTHEN and prj.conf sets CONFIG_BT_SMP_ENFORCE_MITM=y, so
NO_PIN with no auth callbacks would leave every characteristic returning
BT_ATT_ERR_AUTHENTICATION. Falling back to RANDOM_PIN keeps the link
usable instead of silently broken. Also re-formatted this file with the
project's .trunk/configs/.clang-format (Linux braces, 4-space indent,
130-col) — the previous lint-fix commit a2aca3234 accidentally used the
default LLVM style here, which CI's clang-format would have rejected.
Build verified: pio run -e nrf54l15dk passes, RAM 47.4%, Flash 28.6%.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address remaining Copilot review threads
Round 2/3 review fixes — bugs first, then docs/portability:
BLE concurrency (NRF54L15Bluetooth.cpp):
- onNowHasData / sendLog / BleDeferredThread / shutdown: acquire
active_conn under ble_mutex via new acquire_active_conn() helper so
disconnected_cb can't free the conn between the null check and
bt_conn_ref/bt_gatt_notify (use-after-unref).
- write_toradio: reject writes that exceed MAX_TO_FROM_RADIO_SIZE with
ATT_ERR_INVALID_ATTRIBUTE_LEN instead of returning success and silently
dropping the payload (would hide failed config writes from the phone).
- start_advertising: truncate the device name to fit the 31-byte legacy
scan-response limit and switch to BT_DATA_NAME_SHORTENED so
bt_le_adv_start() doesn't reject the payload when the name approaches
CONFIG_BT_DEVICE_NAME_MAX=32.
Linker / portability:
- main.h: drop the rp2040Loop() forward declaration that had no
definition and no callers — would surface as a link error if any RP2040
build added a call to the symbol.
- nrf54l15_arduino.cpp: transfer16() now uses static __aligned(4) DMA
buffers (matching transfer()), removing the EasyDMA-reachability hazard
of caller-stack buffers on this part.
Filesystem (InternalFileSystem.h):
- usedBytes(): return real usage from fs_statvfs() instead of 0 so OTA
/ range-test free-space guards work.
- rewindDirectory(): close the dir before reopening — Zephyr fs_dir_t has
no rewind, and re-fs_opendir on an open handle leaks LittleFS state.
Crash handler (nrf54l15_main.cpp):
- After the stack walk, busy-wait 50 ms to flush RTT/printk and call
sys_reboot(SYS_REBOOT_COLD) directly so the saved_crash record is
actually reported on the next boot. Default Zephyr config has
RESET_ON_FATAL_ERROR=n, so the previous k_fatal_halt() spun forever.
Generalization / config:
- PhoneAPI.cpp: replace the NRF54L15_DK ifdef with a
MESHTASTIC_EXCLUDE_FILES_MANIFEST capability flag (defined in the
nrf54l15dk env) so future variants can opt in/out without touching
shared code.
- variants/nrf54l15/nrf54l15.ini: parameterize libdeps include paths via
${PIOENV} so additional nRF54L15 envs sharing nrf54l15_base don't break.
- prj.conf: drop the stale "36 KB storage_partition" comments — the DK
overlay reclaims slot1 to ~700 KB and runtime size comes from
FIXED_PARTITION_SIZE.
- nrf54l15dk overlay: remove the zephyr,console / zephyr,shell-uart
chosen entries that conflicted with CONFIG_UART_CONSOLE=n + RTT
console; keep uart30 enabled so swapping the console is one Kconfig
flip away.
Build: nrf54l15dk SUCCESS (flash 28.6%, RAM 47.4%); wiznet_5500_evb_pico2
SUCCESS (verifies the shared main.h change).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15dk): use PRIVATE_HW (255) for custom_meshtastic_hw_model
Per @thebentern's review: the nRF54L15-DK is a development kit, not a
canonical Meshtastic SKU, so it falls under HardwareModel::PRIVATE_HW
(255) — the same enum value already used at runtime via HW_VENDOR. The
placeholder 132 is removed; no dedicated enum number will be assigned
for DK boards. Slug stays NRF54L15_DK as a human-readable identifier.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): unstarve bt_long_wq so SC pairing completes
bt_pub_key_gen() runs the ECC P256 key generation on bt_long_wq. At default
prio=10 (preemptible) and stack=1400 it gets starved by Meshtastic app
threads at boot — sc_public_key stays NULL for minutes, smp_public_key()
defers with SMP_FLAG_PKEY_SEND, and every SC pairing attempt stalls right
after the public-key exchange. iOS shows "Connecting…" forever with no
PIN prompt; bleak/CLI fails the first CCC notify write with
"Protocol Error 0x05: Insufficient Authentication".
Set CONFIG_BT_LONG_WQ_PRIO=0 (highest preemptible, ties with main) and
CONFIG_BT_LONG_WQ_STACK_SIZE=4096 (margin for the P256M driver frames).
Validated E2E with iOS Meshtastic app: bt_smp_pkey_ready fires within ~40 s
of boot, 20 SC Passkey Entry rounds complete with matching pcnf/cfm,
encrypt 0x01 / sec_level 0x04 (Authenticated MITM), bonded=1.
* feat(nrf54l15): hardware I2C bus via TWIM30 + sensor telemetry
Adds the Arduino TwoWire layer for the nRF54L15-DK so Meshtastic's
sensor drivers can talk to external I2C devices over the hardware
TWIM30 peripheral.
Bus binding:
- &uart30 disabled in the board overlay (peripheral instance 30 is
shared between UARTE30 / TWIM30 / SPIM30 — pick one). Console stays
on RTT via CONFIG_RTT_CONSOLE.
- New i2c30_default / i2c30_sleep pinctrl with SDA=P0.03 / SCL=P0.04.
External 4.7 kOhm pull-ups required on both lines.
- &i2c30 enabled at I2C_BITRATE_FAST (400 kHz).
- button_3 (SW3, P0.04) deleted from DTS so the pad can be claimed by
i2c30 pinctrl; SW3 is still wired to the pad on the DK, do not press
it during I2C use or it will short SCL to GND.
Arduino layer:
- src/platform/nrf54l15/Wire.cpp resolves the DT node at compile time
via DEVICE_DT_GET(DT_NODELABEL(i2c30)) and dispatches Arduino's
beginTransmission / write / endTransmission / requestFrom to
i2c_write / i2c_write_read / i2c_read. Buffer is sized to 256 bytes
for forward compatibility with the SE050 secure element on the
custom PCB.
- Wire.h drops the prior compile-only stubs and exposes the real
TwoWire surface.
- Arduino.h: BitOrder becomes an enum (not #define) so Adafruit_BusIO's
`typedef BitOrder BusIOBitOrder;` compiles.
Variant + build flags:
- nrf54l15.ini flips HAS_WIRE / HAS_SENSOR / HAS_TELEMETRY from 0 to 1
and cherry-picks the sensor libs Meshtastic needs (BusIO, Sensor,
BMP280, BME280, INA219/226/260/3221, SHT4X). The full
environmental_base group is avoided because it pulls
Adafruit_SSD1306 / Adafruit_GFX which rely on Arduino pin macros the
Zephyr shim does not implement.
- nrf54l15dk variant.h defines PIN_WIRE_SDA / PIN_WIRE_SCL for parity
with the Arduino convention used by other variants. The actual bus
wiring is fixed by the overlay pinctrl above.
Validated 2026-05-14/15 on the DK with BMP280 @ 0x76 (temperature +
barometric pressure) and INA3221 @ 0x42 (rail voltage / current);
EnvironmentTelemetry / PowerTelemetry packets transmit successfully
over LoRa.
Footprint cost on nrf54l15dk: +45 KB flash, +1.7 KB RAM.
* feat(nodedb): honor USERPREFS for environment telemetry on first boot
installDefaultConfig() now respects two new compile-time prefs:
USERPREFS_CONFIG_ENV_TELEM_UPDATE_INTERVAL
USERPREFS_CONFIG_ENVIRONMENT_MEASUREMENT_ENABLED
The mobile apps enforce a 30 min floor on environment_update_interval
in the settings UI, which makes short-interval bring-up testing of new
sensor hardware painful — you have to wait half an hour for the first
LoRa packet to confirm wiring + driver. With these prefs baked into
the variant, the firmware can ship a freshly-flashed device that
broadcasts on a shorter cadence (e.g. 900 s) the moment storage_partition
is empty.
Both prefs are gated on #ifdef so the behavior is unchanged for any
variant that does not opt in. Documented in userPrefs.jsonc with the
existing telemetry-interval pref block.
* fix(nrf54l15): allow multiple bonded BLE peers
CONFIG_BT_MAX_PAIRED defaults to 1, so once the first peer (e.g. an
iOS phone) has paired and bonded, every subsequent pairing attempt
from a different MAC fails inside bt_keys_get_addr() with no free
key slot — the host returns BT_SECURITY_ERR_KEY_DOES_NOT_EXIST and
the second peer never gets past SMP.
Raise the slot count to 4 so the device can simultaneously hold an
iOS phone, a Windows host, a Linux host, and one spare bond. Add
BT_KEYS_OVERWRITE_OLDEST so that once the table fills, the LRU peer
is evicted on the next pairing rather than rejecting the new peer.
This matches the behavior other Meshtastic ports already provide
(nRF52 uses CONFIG_BT_PERIPHERAL_PRIO_CONN with similar semantics).
Discovered while bringing up the Python CLI on Windows alongside
the existing iOS bond.
* fix(nrf54l15): zero-initialize TwoWire buffers + clang-format Wire
cppcheck on every CI target (esp32s3, rp2040, rp2350, nrf52840, ...) was
failing the build with two `uninitMemberVar` warnings on TwoWire's
constructor: `txBuf` and `rxBuf` (256-byte arrays) were not initialized.
Even though the buffers are only read after txLen/rxLen is set, leaving
them uninitialized is a footgun if any future caller bypasses the
len-set step. Use C++11 value-initialization in the member initializer
list — costs ~512 B of memset at boot, gains a clean cppcheck pass and
defensive-against-future-changes semantics.
Also reformat Wire.{cpp,h} with the project's `.trunk/configs/.clang-format`
config so the Trunk Check Runner passes — clang-format moved the
`<errno.h>` include before the Zephyr-namespaced ones in Wire.cpp and
collapsed two inline overloads to single lines in Wire.h.
* fix(AdminModule): remove dead OUTPUT_GPIO_PIN/GpioOutputModule references
OUTPUT_GPIO_PIN is never defined and modules/GpioOutputModule.h doesn't
exist in the codebase; all #ifdef OUTPUT_GPIO_PIN branches were dead code
introduced by the nRF54L15-DK variant commit. Strips the include, the
output_gpio_enabled OFF→ON/ON→OFF transition logic in handleSetConfig(),
and the digitalRead() reflection in handleGetConfig().
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix missing potential null termination in xmodem filename handling
The packet size max is 128 bytes, and the filename is 128 bytes, so
potentially there is no NUL at the end. use strlcpy() as that takes
care of null termination even if buffer size is exceeded.
* Protect against theoretical buffer overflows in BLE logging
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Resolve naming conflict of Syslog class with namespace
* do not include libpax headers if pax counter is excluded
* clean only top-level sdkconfigs, keep them in the variants directories
* Fix code formatting
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
* First try at multimessage storage and display
* Nrf built issue fix
* Message view mode
* Add channel name instead of channel slot
* trunk fix
* Fix for DM threading
* fix for message time
* rename of view mode to Conversations
* Reply in thread feature
* rename Select View Mode to Select Conversation
* dismiss all live fix
* Messages from phone show on screen
* Decoupled message packets from screen.cpp and cleaned up
* Cannedmessage cleanup and emotes fixed
* Ack on messages sent
* Ack message cleanup
* Dismiss feature fixed
* removed legacy temporary messages
* Emote picker fix
* Memory size debug
* Build error fix
* Sanity checks are okay sometimes
* Lengthen channel name and finalize cleanup removal of Broadcast
* Change DM to @ in order to unify on a single method
* Continue unifying display, also show message status on the "isMine" lines
* Add context for incoming messages
* Better to say "in" vs "on"
* crash fix for confirmation nodes
* Fix outbound labels based to avoid creating delays
* Eink autoscroll dissabled
* gating for message storage when not using a screen
* revert
* Build fail fix
* Don't error out with unset MAC address in unit tests
* Provide some extra spacing for low hanging characters in messages
* Reorder menu options and reword Respond
* Reword menus to better reflect actions
* Go to thread from favorite screen
* Reorder Favorite Action Menu with simple word modifications
* Consolidate wording on "Chats"
* Mute channel fix
* trunk fix
* Clean up how muting works along with when we wake the screen
* Fix builds for HELTEC_MESH_SOLAR
* Signal bars for message ack
* fix for notification renderer
* Remove duplicate code, fix more Chats, and fix C6L MessageRenderer
* Fix to many warnings related to BaseUI
* preset aware signal strength display
* More C6L fixes and clean up header lines
* Use text aligns for message layout where necessary
* Attempt to fix memory usage of invalidLifetime
* Update channel mute for adjusted protobuf
* Missed a comma in merge conflicts
* cleanup to get more space
* Trunk fixes
* Optimize Hi Rez Chirpy to save space
* more fixes
* More cleanup
* Remove used getConversationWith
* Remove unused dismissNewestMessage
* Fix another build error on occassion
* Dimiss key combo function deprecated
* More cleanup
* Fn symbol code removed
* Waypoint cleanup
* Trunk fix
* Fixup Waypoint screen with BaseUI code
* Implement Haruki's ClockRenderer and broadcast decomposeTime across various files.
* Revert "Implement Haruki's ClockRenderer and broadcast decomposeTime across various files."
This reverts commit 2f65721774.
* Implement Haruki's ClockRenderer and broadcast decomposeTime across various files. Attempt 2!
* remove memory usage debug
* Revert only RangeTestModule.cpp change
* Switch from dynamic std::string storage to fixed-size char[]
* Removing old left over code
* More optimization
* Free Heap when not on Message screen
* build error fixes
* Restore ellipsis to end of long names
* Remove legacy function renderMessageContent
* improved destination filtering
* force PKI
* cleanup
* Shorten longNames to not exceed message popups
* log messages sent from apps
* Trunk fix
* Improve layout of messages screen
* Fix potential crash for undefined variable
* Revert changes to RedirectablePrint.cpp
* Apply shortening to longNames in Select Destination
* Fix short name displays
* Fix sprintfOverlappingData issue
* Fix nullPointerRedundantCheck warning on ESP32
* Add "Delete All Chats" to all chat views
* Improve getSafeNodeName / sanitizeString code.
* Improve getSafeNodeName further
* Restore auto favorite; but only if not CLIENT_BASE
* Don't favorite if WE are CLIENT_BASE role
* Don't run message persistent in MUI
* Fix broken endifs
* Unkwnown nodes no longer show as ??? on message thread
* More delete options and cleanup of code
* fix for delete this chat
* Message menu cleanup
* trunk fix
* Clean up some menu options and remove some Unit C6L ifdefines
* Rework Delete flow
* Desperate times call for desperate measures
* Create a background on the connected icon to reduce overlap impact
* Optimize code for background image
* Fix for Muzi_Base
* Trunk Fixes
* Remove the up/down shortcut to launch canned messages (#8370)
* Remove the up/down shortcut to launch canned messages
* Enabled MQTT and WEBSERVER by default (#8679)
Signed-off-by: kur1k0 <zhuzirun@m5stack.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
---------
Signed-off-by: kur1k0 <zhuzirun@m5stack.com>
Co-authored-by: Riker <zhuzirun@m5stack.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Correct string length calculation for signal bars
* Manual message scrolling
* Fix
* Restore CannedMessages on Home Frame
* UpDown situational destination for textMessage
* Correct up/down destinations on textMessage frame
* Update Screen.h for handleTextMessage
* Update Screen.cpp to repair a merge issue
* Add nudge scroll on UpDownEncoder devices.
* Set nodeName to maximum size
* Revert "Set nodeName to maximum size"
This reverts commit e254f39925.
* Reflow Node Lists and TLora Pager Views (#8942)
* Add files via upload
* Move files into the right place
* Short or Long Names for everyone!
* Add scrolling to Node list
* Pagination fix for Latest to oldest per page
* Page counters
* Dynamic scaling of column counts based upon screen size, clean up box drawing
* Reflow Node Lists and TLora Pager Views (#8942)
* Add files via upload
* Move files into the right place
* Short or Long Names for everyone!
* Add scrolling to Node list
* Pagination fix for Latest to oldest per page
* Page counters
* Dynamic scaling of column counts based upon screen size, clean up box drawing
* Update exempt labels for stale bot workflow
Adds triaged and backlog to the list of exempt labels.
* Update naming of Frame Visibility toggles
* Fix to scrolling
* Fix for content cutting off when from us
* Fix for "delete this chat" now it does delete the current one
* Rework isHighResolution to be an enum called ScreenResolution
* Migrate Unit C6L macro guards into currentResolution UltraLow checks
* Mistakes happen - restoring NodeList Renderer line
---------
Signed-off-by: kur1k0 <zhuzirun@m5stack.com>
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Riker <zhuzirun@m5stack.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: whywilson <m.tools@qq.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
As reported by @jstockdale, when writing coloured logs we were
writing the full string, including a null terminator. This caused
issues for programs consuming our logs. The fix as identified is
not to write the null.
Fixes https://github.com/meshtastic/firmware/issues/5945
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
security option. Per discussion in https://github.com/meshtastic/firmware/issues/4375
no need to preserve the old options when changing to this new simpler
single boolean because they were newish, rarely used and only for 'advanced'
developers.
* Adds ASCII logs useful to portudino
Activates ASCII log option when stdout is not a terminal. This is
generally the right thing to do; if not, the behavior can be
overridden in config.yaml using AsciiLogs under Logging. The result
is reasonable system logs for portudino when running under systemd or
the like.
Signed-off-by: Christopher Hoover <ch@murgatroid.com>
Co-authored-by: Christopher Hoover <ch@murgatroid.com>
* Re-implement PKI from #1509
co-authored-by: edinnen <ethanjdinnen@protonmail.com>
* Set the key lengnth to actually make PKI work.
* Remove unused variable and initialize keys to null
* move printBytes() to meshUtils
* Don't reset PKI key son reboot unless needed.
* Remove double encryption for PKI messages
* Cleanup encrypt logic
* Add the MESHTASTIC_EXCLUDE_PKI option, and set it for minimal builds. Required for STM32 targets for now.
* Use SHA-256 for PKI key hashing, and add MESHTASTIC_EXCLUDE_PKI_KEYGEN for STM32
* Fix a crash when node is null
* Don't send PKI encrypted packets while licensed
* use chIndex 8 for PKI
* Don't be so clever, that you corrupt incoming packets
* Pass on channel 8 for now
* Typo
* Lock keys once non-zero
* We in fact need 2 scratch buffers, to store the encrypted bytes, unencrypted bytes, and decoded protobuf.
* Lighter approach to retaining known key
* Attach the public key to PKI decrypted packets in device memory
* Turn PKI back off for STM32 :(
* Don't just memcp over a protobuf
* Don't PKI encrypt nodeinfo packets
* Add a bit more memory logging around nodeDB
* Use the proper macro to refer to NODENUM_BROADCAST
* Typo fix
* Don't PKI encrypt ROUTING (naks and acks)
* Adds SecurityConfig protobuf
* Add admin messages over PKI
* Disable PKI for the WIO-e5
* Add MINIMUM_SAFE_FREE_HEAP macro and set to safe 1.5k
* Add missed "has_security"
* Add the admin_channel_enabled option
* STM32 again
* add missed configuration.h at the top of files
* Add EXCLUDE_TZ and RTC
* Enable PKI build on STM32 once again
* Attempt 1 at moving PKI to aes-ccm
* Fix buffers for encrypt/decrypt
* Eliminate unused aes variable
* Add debugging lines
* Set hash to 0 for PKI
* Fix debug lines so they don't print pointers.
* logic fix and more debug
* Rather important typo
* Check for short packets before attempting decrypt
* Don't forget to give cryptoEngine the keys!
* Use the right scratch buffer
* Cleanup
* moar cleanups
* Minor hardening
* Remove some in-progress stuff
* Turn PKI back off on STM32
* Return false
* 2.5 protos
* Sync up protos
* Add initial cryptography test vector tests
* re-add MINIMUM_SAFE_FREE_HEAP
* Housekeeping and comment fixes
* Add explanatory comment about weak dh25519 keys
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Macro to trace log all MeshPackets as JSON
* Comment
* Add trace logging to file for native target
* bytes to hex
* Add time_ms
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* MESHTASTIC_EXCLUDE_WIFI and HAS_WIFI cleanup...
Our code was checking HAS_WIFI and the new MESHTASTIC_EXCLUDE_WIFI
flags in various places (even though EXCLUDE_WIFI forces HAS_WIFI
to 0). Instead just check HAS_WIFI, only use EXCLUDE_WIFI inside
configuration.h
* cleanup: use HAS_NETWORKING instead of HAS_WIFI || HAS_ETHERNET
We already had HAS_NETWORKING as flag in MQTT to mean 'we have
tcpip'. Generallize that and move it into configuration.h so that
we can use it elsewhere.
* Use #pragma once, because supported by gcc and all modern compilers
instead of #ifdef DOTHFILE_H etc...
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* New UUID
* New log radio characteristic with LogRecord protobuf
* LogRecord
* Merge derp
* How did you get there
* Trunk
* Fix length
* Remove assert
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* WIP log characteristic
* Bluetooth logging plumbing
* Characteristic
* Callback
* Check for nullptr
* Esp32 bluetooth impl
* Formatting
* Add thread name and log level
* Add settings guard
* Remove comments
* Field name
* Fixes esp32
* Open it up
* Whoops
* Move va_end past our logic
* Portduino multiple logging levels
* Fixes based on GPSFan work
* Fix derped logic
* Correct size field for AID message
* Reformat to add comments, beginning of GPS rework
* Update PM2 message for Neo-6
* Correct ECO mode logic as ECO mode is only for Neo-6
* Cleanup ubx.h add a few more comments
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Move to Portduino's getMacAddr()
* Add ST7735/S screen support
* Push Raspbian support into native target
* Remove latent pigpio references.
* CardKB defensive programming
* Adds configurable spidev
* Fixes to build on Fedora 40
* ENUMs are not #defines. Pull latest portduino
* Add more configuration options for SPI displays
* Add config.yaml option to set DIO3_TCXO_VOLTAGE
* change tft clear() to fillScreen()
Maintains compatability with ESPI driver.
* Adds TXen and RXen pins to portduino
* Add -c --config options to specify config file
* Fail when a specified config file is unavailable
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Implement override_console_serial_port
* It's opposite day in Logictown
* Try to use native serial types for platforms
* Fix for s3
* Trunk
* Screw it... just declare as Print and handle init
* Alright, chatty kathy
* Missed a spot
* I'll take "Kill that FIXME" for 800, Alex
* Badunkadunk
* Refactor out a lot of duplicated code
* Boogers
* Okay I probably should stop changing everything
- Skip a lot of duplicate code
- add a hexDump output - might come in handy
- refactor directory names
- remove unused debugOut that was generating template errors
