mirror of
https://github.com/meshtastic/firmware.git
synced 2026-06-16 04:30:18 -04:00
24c4162a75
* Standardize PMU IRQ handling and enable power button as cancel on tbeam s3 * Original T-beam, too
76 lines
2.3 KiB
C
76 lines
2.3 KiB
C
// #define BUTTON_NEED_PULLUP // if set we need to turn on the internal CPU pullup during sleep
|
|
|
|
#define I2C_SDA 21
|
|
#define I2C_SCL 22
|
|
|
|
#define BUTTON_PIN 38 // The middle button GPIO on the T-Beam
|
|
#define BUTTON_ACTIVE_LOW true
|
|
#define BUTTON_ACTIVE_PULLUP true
|
|
#define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.
|
|
|
|
#define LED_STATE_ON 0 // State when LED is lit
|
|
#define LED_POWER 4 // Newer tbeams (1.1) have an extra led on GPIO4
|
|
|
|
// TTGO uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
|
|
// not found then probe for SX1262
|
|
#define USE_RF95 // RFM95/SX127x
|
|
#define USE_SX1262
|
|
#define USE_SX1268
|
|
|
|
#define LORA_DIO0 26 // a No connect on the SX1262 module
|
|
#define LORA_RESET 23
|
|
#define LORA_DIO1 33 // SX1262 IRQ
|
|
#define LORA_DIO2 32 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
|
|
|
#ifdef USE_SX1262
|
|
#define SX126X_CS LORA_CS // FIXME - we really should define LORA_CS instead
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
// Not really an E22 but TTGO seems to be trying to clone that
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
|
// Internally the TTGO module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for the sx1262interface
|
|
// code)
|
|
#endif
|
|
|
|
// Voiding more warranties.
|
|
#define PMU_IRQ 35
|
|
#define PMU_POWER_BUTTON_IS_CANCEL // maps a short click of the power button to a cancel action (turning off the screen)
|
|
|
|
#define HAS_AXP192
|
|
#define GPS_UBLOX
|
|
#define GPS_RX_PIN 34
|
|
#define GPS_TX_PIN 12
|
|
// #define GPS_DEBUG
|
|
|
|
// Used when the display shield is chosen
|
|
#ifdef USE_ST7796
|
|
|
|
#undef EXT_NOTIFY_OUT
|
|
#undef LED_STATE_ON
|
|
#undef LED_POWER
|
|
|
|
#define HAS_CST226SE 1
|
|
#define HAS_TOUCHSCREEN 1
|
|
// #define TOUCH_IRQ 35 // broken in this version of the lib 0.3.1
|
|
#ifndef TOUCH_IRQ
|
|
#define TOUCH_IRQ -1
|
|
#endif
|
|
#define USE_VIRTUAL_KEYBOARD 1
|
|
|
|
#define ST7796_NSS 25
|
|
#define ST7796_RS 13 // DC
|
|
#define ST7796_SDA 14 // MOSI
|
|
#define ST7796_SCK 15
|
|
#define ST7796_RESET 2
|
|
#define ST7796_MISO -1
|
|
#define ST7796_BUSY -1
|
|
#define VTFT_LEDA 4
|
|
#define TFT_SPI_FREQUENCY 60000000
|
|
#define TFT_HEIGHT 222
|
|
#define TFT_WIDTH 480
|
|
#define BRIGHTNESS_DEFAULT 100 // Medium Low Brightness
|
|
#define SCREEN_TRANSITION_FRAMERATE 5 // fps
|
|
#endif |