* Deprecate forwarding for invalid hop_start
* Add pre-hop packet drop policy
* Log ignored rebroadcasts for pre-hop packets
* Respect pre-hop policy ALLOW in routing gates
* Exempt local packets from pre-hop drop policy
* Format pre-hop log line
* Add MODERN_ONLY rebroadcast mode for pre-hop packets
* Simplify implementation for drop packet only behaviour
* Revert formatting-only changes
* Match ReliableRouter EOF formatting
* Make pre-hop drop a build-time flag
* Rework to compile/build flag MESHTASTIC_PREHOP_DROP
* Set MESHTASTIC_PREHOP_DROP off by default
* Inline pre-hop hop_start validity check
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jord <650645+DivineOmega@users.noreply.github.com>
The Seeed Xiao S3 Kit's default GPS is an L76K which operates at 9600 baud, so when this variant was defined that baud rate was specified.
However, this is a development board and it is expected that users can attach their own devices. This includes GPS, which may operate at a different baud rate. The current fixed baud rate prevents this, so this patch removes that setting.
This will revert to the regular automatic probe method. This will successfully detect the L76K as before (the same speed as before since 9600 baud is the first baud rate checked), but also allow other GPSes at other baud rates to be detected.
Thanks to @ScarpMarc for the report
Fixes https://github.com/meshtastic/firmware/issues/9373#issuecomment-3774802763
* Add ESP32 Power Management lessons learned document
Documents our experimentation with ESP-IDF DFS and why it doesn't
work well for Meshtastic (RTOS locks, BLE locks, USB issues).
Proposes simpler alternative: manual setCpuFrequencyMhz() control
with explicit triggers for when to go fast vs slow.
* Addition of traffic management module
* Fixing compile issues, but may still need to update protobufs.
* Fixing log2Floor in cuckoo hash function
* Adding support for traffic management in PhoneAPI.
* Making router_preserve_hops work without checking if the previous hop was a router. Also works for CLIENT_BASE.
* Adding station-g2 and portduino varients to be able to use this module.
* Spoofing from address for nodeinfo cache
* Changing name and behavior for zero_hop_telemetry / zero_hop_position
* Name change for exhausting telemetry packets and setting hop_limit to 1 so it will be 0 when sent.
* Updated hop logic, including exhaustRequested flag to bypass some checks later in the code.
* Reducing memory on nrf52 nodes further to 12 bytes per entry, 12KB total using 8 bit hashes with 0.4% collision. Probably ok. Adding portduino to the platforms that don't need to worry about memory as much.
* Fixing hopsAway for nodeinfo responses.
* traffic_management.nodeinfo_direct_response_min_hops -> traffic_management.nodeinfo_direct_response_max_hops
* Removing dry run mode
* Updates to UnifiedCacheEntry to use a common cache, created defaults for some values, reduced a couple bytes per entry by using a resolution-scale time selection based on configuration value.
* Enhance traffic management logging and configuration. Updated log messages in NextHopRouter and Router to include more context. Adjusted traffic management configuration checks in AdminModule and improved cache handling in TrafficManagementModule. Ensured consistent enabling of traffic management across various variants.
* Implement destructor for TrafficManagementModule and improve cache allocation handling. The destructor ensures proper deallocation of cache memory based on its allocation source (PSRAM or heap). Additionally, updated cache allocation logic to log warnings only when PSRAM allocation fails.
* Update TrafficManagementModule with enhanced comments for clarity and improve cache handling logic. Update protobuf submodule to latest commit.
* Creating consistent log messages
* Remove docs/ESP32_Power_Management.md from traffic_module
* Add unit tests for Traffic Management Module functionality
* Fixing compile issues, but may still need to update protobufs.
* Adding support for traffic management in PhoneAPI.
* Making router_preserve_hops work without checking if the previous hop was a router. Also works for CLIENT_BASE.
* Enhance traffic management logging and configuration. Updated log messages in NextHopRouter and Router to include more context. Adjusted traffic management configuration checks in AdminModule and improved cache handling in TrafficManagementModule. Ensured consistent enabling of traffic management across various variants.
* Implement destructor for TrafficManagementModule and improve cache allocation handling. The destructor ensures proper deallocation of cache memory based on its allocation source (PSRAM or heap). Additionally, updated cache allocation logic to log warnings only when PSRAM allocation fails.
* Update TrafficManagementModule with enhanced comments for clarity and improve cache handling logic. Update protobuf submodule to latest commit.
* Add mock classes and unit tests for Traffic Management Module functionality.
* Refactor setup and loop functions in test_main.cpp to include extern "C" linkage
* Update comment to include reduced memory requirements
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Re-arranging comments for programmers with the attention span of less than 5 lines of code.
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update comments in TrafficManagementModule to reflect changes in timestamp epoch handling and memory optimization details.
* bug: Use node-wide config_ok_to_mqtt setting for cached NodeInfo replies.
* Better way to handle clearing the ok_to_mqtt bit
* Add bucketing to cuckoo hashing, allowing for 95% occupied rate before major eviction problems.
* Extend nodeinfo cache for psram devices.
* Refactor traffic management to make hop exhaustion packet-scoped. Nice catch.
* Implement better position precision sanitization in TrafficManagementModule.
* Added logic in TrafficManagementModule to invalidate stale traffic state. Also, added some tests to avoid future me from creating a regression here.
* Fixing tests for native
* Enhance TrafficManagementModule to improve NodeInfo response handling and position deduplication logic. Added tests to ensure local packets bypass transit filters and that NodeInfo requests correctly update the requester information in the cache. Updated deduplication checks to prevent dropping valid position packets under certain conditions.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Fixes this build error:
<command-line>: error: expected unqualified-id before '-' token
/home/<snip>/.platformio/packages/framework-arduinoespressif32/variants/esp32s3/pins_arduino.h:15:22: note: in expansion of macro 'LED_BUILTIN'
15 | static const uint8_t LED_BUILTIN = SOC_GPIO_PIN_COUNT + PIN_RGB_LED;
| ^~~~~~~~~~~
More info: https://github.com/meshtastic/firmware/pull/9122#issuecomment-4028263894
The fix is consistent with variants/esp32s3/heltec_v3/platformio.ini
This commit is intentionally on the develop branch, because it's harmless to
develop branch, and makes us more ready for pioarduino when the time comes.
Heltec v4 introduced in: https://github.com/meshtastic/firmware/pull/7845
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
socketSendUDP() calls yield() while waiting for SEND_OK, allowing the
cooperative scheduler to run AsyncUDP::runOnce(). When runOnce() calls
parsePacket() on the same socket during an active send, the multicast
loopback packet arriving from the switch produces a garbled 8-byte RX
header (wrong source IP, wrong payload length), leading to protobuf
decode errors in UdpMulticastHandler.
Add a volatile isSending flag that writeTo() sets around endPacket()
(the only yield point). runOnce() checks this flag and skips
parsePacket() while a send is in progress. Loopback packets stay
buffered in the W5100S RX buffer and are read cleanly on the next
poll cycle.
Also propagate writeTo() return value in UdpMulticastHandler::onSend()
instead of unconditionally returning true.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Nodelist cleanup
* Trunk fix
* getTextWidth cleanup
Updated the lambda to cache width in textW and reuse it instead of repeatedly calling getTextWidth(text) for unchanged text.
* Putting back hopAway ==0 condition as mentioned relayed signal is missleading
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update Heltec Tracker v2 to version KCT8103L.
* Fixed the issue of inaccurate comments.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
P0.04 is a digital power-enable pin for the NTC/LUX sensors, not an ADC
input. The old code was calling analogRead() on a floating GPIO that
happened to read ~mid-rail, coincidentally producing reasonable
temperature values.
- Rename T1000X_VCC_PIN to T1000X_SENSOR_EN_PIN and drive it HIGH in
initVariant() for both T1000-E and T1000-S variants
- Read BATTERY_PIN (with ADC_MULTIPLIER) instead, clamped to the 3.0V
LDO output (NTC_REF_VCC) for the NTC resistance calculation
* Cardputer Kit
BMI270 WIP
* BMI270 support
* verify that the number of bytes read matches the requested length
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* trunk'd
* remove excessive logging
* Kick the screen when unsleeping
* Update the st7789 library, and enable displayon and displayoff
* Battery detection
* Default to arrow keys and enter, while in menus.
* Enable Backlight control
* Update src/detect/ScanI2CTwoWire.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* updateState method now accepts shouldRequestFocus parameter for better maintainability
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add Portduino Enable pins
* Add hat plus custom fields
* Punt on the GPIO device detection for now
* Simplify TX_GAIN_LORA for RAK13302
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
This fixes builds in very clean environment with default build target (e.g.
-t buildfs *not* explicitly specified).
Tested: pio run -e heltec-v3
Fixes#9035
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Adds ROUTER_LATE and CLIENT_BASE to preferred rebroadcaster check
(skip unsolicited NodeInfo) and prevents ROUTER_LATE from setting
rebroadcast mode to NONE, which would silently break relaying.
ROUTER_LATE is an infrastructure relay that should use the same power
assumptions, interval defaults, and LoRa wake behavior as ROUTER.
Without this, ROUTER_LATE uses client-class defaults and will not
wake on LoRa activity from deep sleep, making it a broken relay.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER_LATE already has high base intervals and should not be further
scaled by congestion. TAK_TRACKER is a tracker variant that should
skip congestion scaling like TRACKER does.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER and ROUTER_LATE should not accumulate favorites by sending DMs.
Also replaces magic number 12 with meshtastic_Config_DeviceConfig_Role_CLIENT_BASE.
ROUTER_LATE should be treated as an impolite telemetry role like
ROUTER, responding to multi-hop broadcast requests and using
aggressive send timing without channel utilization checks.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER_LATE now preserves node_info_broadcast_secs during factory
reset and auto-enables Store & Forward server mode, matching ROUTER
infrastructure behavior.
* refactor: update throttling factor calculation and add unit tests for scaling behavior
* refactor: adjust throttling factor calculation for improved accuracy in different configurations
* Update src/mesh/Default.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/mesh/Default.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* refactor: enhance throttling factor calculation and introduce pow_of_2 utility function
* refactor: improve expected ms calculation in unit tests for Default::getConfiguredOrDefaultMsScaled
* refactor: improve scaling logic for routers and sensors in computeExpectedMs function
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improve resource cleanup on connection close
* Copilot had some good feedback. Let's just make the api a unique pointer
* Update src/mesh/api/ServerAPI.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Copilot stupidly suggesting we call protected methods
* Gotta do it in the superclasses as well
* Fix moar
* Refactor MQTT unit test to ensure proper subscription handling and clear side effects
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Add ESP32 Power Management lessons learned document
Documents our experimentation with ESP-IDF DFS and why it doesn't
work well for Meshtastic (RTOS locks, BLE locks, USB issues).
Proposes simpler alternative: manual setCpuFrequencyMhz() control
with explicit triggers for when to go fast vs slow.
* Added a lambda function to clear startup output in the MQTT unit test to ensure a clean state before and after the MQTT subscription process.
getByIndex allocates memory and returns dummy channel whenever
chIndex validation fails. Comment implies this may happen
when malformed packet is received. The fix changes implementation
so static dummyChannel is returned in such case.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
