* fix(nrf52): serialise the warm-node ring against LittleFS on the shared flash cache
On nRF52840 the warm-node store writes its 3-page record ring straight through
flash_nrf5x_write/erase/flush, holding only spiLock. Every LittleFS writer instead
holds Adafruit_LittleFS's own mutex, and two of them run on other tasks entirely:
Bluefruit's bond saves on the callback task, and - since phone config writes moved
into BLE context - a whole saveToDisk on the BLE task. Neither takes spiLock.
Both writers share one 4 KB page cache, one SoftDevice flash semaphore and one
result word. flash_cache_write repoints that cache when the requested page differs
from the cached one, so a second writer arriving mid-write flushes the first
writer's page and re-points the buffer; the first writer's remaining memcpy then
lands in the wrong page's image. Ring records end up inside LittleFS metadata, or
the reverse. The collision also exhausts the flash layer's 20 x 1 ms busy-retry
budget against an 85 ms page erase, and flash_cache_flush discards the failure, so
32 LittleFS blocks vanish with no error reaching the filesystem. What the user sees
is a torn directory pair on the next mount, a format, and critical error 13.
Take the filesystem mutex in the five ring entry points that reach flash, after
spiLock and never before - the order every existing path already uses. The ring
touches no LittleFS call itself, so the non-recursive mutex is never re-entered.
Longest new hold is a page rotation at roughly half a second, against a 2 s
supervision timeout and a 90 s watchdog. Non-nRF52840 backends are untouched.
* fix(nodedb): make saveProto report a failed readback or rename
SafeFile::close() already verifies the .tmp by hash and renames it over the
live file, and saveProto captured that result, logged it, and then returned
the pb_encode status alone. A torn or half-programmed page therefore counted
as a successful save: for the fullAtomic files the old contents silently
survived, for nodes.proto (written in place) the file was simply gone, and
saveToDisk's recovery path never fired for the one failure it exists for.
* fix(nodedb): retry a failed save before formatting, and never format on a low rail
saveToDisk answered any failed write with an immediate fsFormat(), which is
where most "critical error 12/13" reports and the total config wipe behind
them come from. A write that fails once is far more often a busy SoftDevice
or a VDD dip mid-save than a corrupt filesystem, so:
- retry twice, 150 ms apart, re-checking powerHAL_isPowerLevelSafe() before
each attempt and before the format; on a low rail return false and leave
the filesystem alone (the next save lands once the rail recovers, and boot
already waits for a safe level)
- check fsFormat()'s result instead of assuming it worked
- after a successful format rewrite every segment, not only the ones this
call asked for: the format took config.proto and the node identity with it,
so a nodes-only save that ended in a format used to come back up as a new
node
- with encrypted storage a format also destroys the DEK; skip the resave
rather than land the private key and PSKs on flash in plaintext
RP2040 feeds its watchdog across the delays, as the neighbouring code does.
* fix(nrf52): quiesce flash before every software reset and power-off
The Adafruit flash layer keeps one 4 KB page image and one SoftDevice flash
semaphore for the whole chip. Every reset path we own - Power::reboot(),
enterDfuMode() (admin enter_dfu_mode_request, which arrives on the BLE task
since #10967), cpuDeepSleep()'s reset and system-off arms, and the
wio-t1000-s secure DFU handler - went straight to NVIC_SystemReset or
sd_power_system_off while another task could be half-way through a page
program or erase. A reset in that window leaves the page erased or partly
programmed; LittleFS finds the torn metadata on the next mount and the
corruption handler formats the filesystem.
nrf52FlashQuiesce() takes spiLock and the LittleFS mutex, waits out whatever
write is in flight, flushes the page cache, and keeps both locks because the
caller resets next. The corruption-reboot handler and __assert_func are left
alone: they run inside the filesystem call stack or a fault, where taking the
mutex would deadlock.
nRF54L is a second copy of these paths since #11867 and still defines
ARCH_NRF52, so it gets the same function on the same core flash layer.
* fix(nrf52): quiesce flash before the library BLE DFU handler jumps to the bootloader
On every board except wio-t1000-s the Nordic DFU service is the framework's
BLEDfu, whose START_DFU handler runs on the callback task and jumps to the
bootloader with no regard for a flash write in progress on the loop task.
That is the OTA path the Apple app and nRF Connect use (Android sends
enter_dfu_mode_request instead, which the previous commit covers).
QuiescingBLEDfu re-installs the control-point write callback after
BLEDfu::begin() and wraps the library's: flush under both locks, then drop
the LittleFS mutex before handing over, because the library reloads the bond
keys through LittleFS on its way to the jump and the mutex is not recursive.
spiLock stays held across the handler: every LittleFS writer on the BLE task
takes it first, the loop task cannot preempt the callback task, and the
handler never blocks after the flush, so nothing can dirty flash before
bootloader_util_app_start(). If the handler returns, nothing jumped, and the
lock is released.
The library callback is a file-static, so it is read back out of the
characteristic through a pointer-to-member obtained via a using-declaration;
that is well-formed C++ and compiles under the pinned GCC 9.3 with LTO.
* test(nodedb): pin the save-failure contract of saveProto and saveToDisk
A failed rename must come back as false from saveProto, a one-off unsafe
rail reading during a write must be retried and land, and a rail still
unsafe at the retry gate must make saveToDisk return false with the
filesystem untouched. The rail is scripted through a strong
powerHAL_isPowerLevelSafe() over the weak native default; on Windows the
default is strong, so only the rename case runs there. The format branch
itself is unreachable natively (a FLASH_CORRUPTION critical error exits
the portduino process), which is what the survival assertions pin.
* fix(nodedb): only format when the filesystem itself is unreadable
Making saveProto honest about write failures gave the recovery path a new way in:
any persistent write failure now reached fsFormat(), which takes every file with
it. A busy or lock-protected nRF52 flash fails every write for as long as it lasts,
so two retries are not enough to tell that apart from a corrupt filesystem, and
guessing wrong costs the node its config, keys and bonds.
Reads settle it. They never touch the SoftDevice write path that a busy flash
fails on, so if /prefs still walks and a stored proto still opens and reads, the
metadata chain is intact and the write failure was transient - return false and
let the caller try again later. Genuine corruption is not silently tolerated: lfs
asserts on it, and the nRF52 handler reboots and formats on the way back up.
Covered by a test that fails without this: a save whose rename cannot succeed,
against an otherwise healthy filesystem, must leave devicestate untouched.
* trunk: exempt Unity test entry points from trufflehog
trufflehog's Lob detector matches "test_" followed by alphanumerics, which
describes every Unity test function name. It fired on a new test in
test_nodedb_save_retry and will fire again on the next suite added. Scoped to
test/**/test_main.cpp, alongside the existing gitleaks exemption for the
synthetic node-DB fixtures.
* fix(nodedb): feed the RP2040 watchdog around the format and the resave
saveToDisk() only feeds the watchdog at the top of each retry. The last
retry, the readable probe, fsFormat() and the five-segment resave then
share one 8 s budget (watchdog_enable in main-rp2xx0.cpp) with no loop
left to feed it. A timeout during the resave leaves the filesystem empty
and the node boots on defaults with a new identity - the exact outcome
this PR exists to prevent, reached by a different road.
Feed once before the probe and again before the resave. Both feeds sit
outside any lock: filesystemStillReadable() takes spiLock itself, and
the format has already released it. ARCH_RP2040 covers rp2040 and rp2350
alike, and the blocks compile out everywhere else, so no other platform
and no native test changes.
Raised by @caveman99 in review.
* fix(nodedb): narrow the save-probe comment and name the full-filesystem case
The comment on filesystemStillReadable() claimed "real corruption asserts
in lfs and formats on reboot". That does hold on nRF52 - nrf52.ini builds
with -DLFS_NO_ASSERT and force-includes cpp_overrides/lfs_util.h, whose
LFS_NO_ASSERT arm routes LFS_ASSERT to the lfs_assert() in main-nrf52.cpp,
which stamps NRF52_MAGIC_LFS_IS_CORRUPT and resets into the format - but
NodeDB.cpp compiles for ESP32, RP2040 and portduino too, where nothing of
the sort is wired up. It is also not true on nRF52 under POFWARN, where
lfs_assert() deliberately skips the stamp. Drop the claim rather than
qualify it three ways.
The log line now names what a field log actually needs to tell apart: a
filesystem that still reads but cannot be written is either busy or full.
Raised by @caveman99 in review.
* fix(sx128x): quiesce flash before the 2.4GHz region reset
reinitChip() saves the region, waits 2 s and resets. On nRF52 that was
the last software reset still going straight to NVIC_SystemReset with a
page program possibly in flight, so "every software reset" in the earlier
commit did not quite hold.
The quiesce stays inside the ARCH_NRF52 arm on purpose. The #else arm
logs and falls through to lora.setCRC() further down, which re-enters
spiBeginTransaction(); a quiesce hoisted above the #if would take spiLock
and never give it back, self-deadlocking portduino and stm32wl. Routing
this through Power::reboot() is wrong for the same class of reason:
setupModules() runs before initLoRa, so its notifyReboot observers and
waypointStore.saveToFlash() are live and would add a flash write to an
aborted radio init.
Raised by @caveman99 in review.
* fix(nrf52): only quiesce on the DFU control write that actually resets
QuiescingBLEDfu wrapped every control-point write, so a write that was
never going to reset still blocked the Bluefruit callback task on spiLock,
forced an early page-cache commit and held back the GATT authorize reply.
Only START_DFU resets; gate on that.
Deliberately no "request->len &&" term. The library's own test is
`request->data[0] == START_DFU` with no length check (BLEDfu.cpp:110 in
both the nRF52 and nRF54 cores), and Bluefruit hands the callback a copy
of a reused event buffer, so a zero-length write carrying a stale 0x01
still resets inside the library. A len term here would let exactly that
reset run unquiesced, which is the case this wrapper exists for. Reading
data[0] is always in bounds: ble_gatts_evt_write_t declares uint8_t
data[1] and the copy covers it.
Raised by @caveman99 in review.
* fix(radio): recover from chip state loss in the RX/TX hot paths too
* fix(radio): address CodeRabbit findings on the hot-path recovery PR (#11680)
* fix(radio): address CodeRabbit findings on the hot-path recovery PR
SX128x: startReceive() still called the old asserting setStandby() before
the new trySetStandby(). The assert fired first, so the recovery path added
below it could never run - the exact chip-state-loss crash this PR exists to
fix was still live on SX128x. Remove the stale call.
LR11x0: resolvedTcxoVoltage was set once after the primary begin() attempts,
but two later paths - firmware recovery and the one-shot firmware update -
call begin() again with tcxoVoltage and never updated it. On a TCXO_OPTIONAL
board that only came up via one of those paths, reinitChip() would recover
with the wrong oscillator setting. Update resolvedTcxoVoltage after each of
those begin() calls too.
LR20x0: reconfigure() discarded RadioLibInterface::reconfigure()'s result -
the band-hop path always returned true regardless, and the same-band path
reused the same flag for chip-programming errors, so a base-class failure
could both mask itself as success and wrongly trigger a full re-init. Track
the base-class result (reconfigureSuccess) separately from the chip result
(standbySuccess), and return the former.
Also shortens the recovery-rationale comments in RadioLibInterface.h and
SX126xInterface.cpp to 1-2 lines per the repo's comment convention, the
rationale now covered once in the base class.
* fix(radio): finish the recovery ladder and stop recovery from rebooting
Follow-up to the CodeRabbit findings, plus two gaps found auditing the
branch against its own intent (never reboot on chip state loss; recover in
place).
RX left off was unrecoverable on an idle node. Every startReceive() call
site is event-driven - RX/TX ISR, the CAD-busy branch, startSend()'s failure
path, init(), reconfigure() - and a radio with RX off cannot raise an RX
interrupt, so nothing re-arms it unless the node happens to transmit or the
user changes config. A listen-only or quiet node stayed deaf for good, which
is worse than the reboot this replaced. main.cpp's existing 60 s AGC tick now
calls periodicRadioMaintenance(), which re-arms RX when rxOffline is set and
otherwise does the AGC reset as before.
In-place repair now gives up rather than retrying forever. After
MAX_CHIP_RECOVERY_FAILURES consecutive failures - a throttle window apart, so
minutes of a provably dead chip - schedule rebootAtMsec, the same deliberate
reboot Portduino already uses for LoRa_in_error. A reboot re-runs init(),
which redoes the power-enable GPIOs, settle delays and TCXO probing that
begin() alone skips. Both counters reset in RadioLibInterface::startReceive(),
the one point every driver reaches only once the chip accepts the RX start.
SX128x: reconfigure()'s recovery reached reinitChip()'s region-mismatch
branch, which rewrites config.lora.region, saves, and calls ESP.restart() /
NVIC_SystemReset(). A runtime recovery must never reboot - that is the crash
this path exists to prevent, and it would fire with a config save pending.
Gated to the boot-time call via a fromInit parameter.
LR20x0: a rejected setRxBoostedGainMode cleared the success flag and so
forced a full fullBegin() chip reset. It is a warn-level cosmetic setting,
treated as warn-only in LR11x0's equivalent, and not a lost-state signature.
Also logs suppressed recovery attempts at debug level; previously a chip that
stayed dead recorded one critical error and then went completely silent.
* fix(radio): count RX re-arms, not re-inits, in the recovery ladder
LR20x0's recoverChipStateLoss() is fullBegin(), which re-arms RX itself but
reports success on begin() alone. A re-init that came back with RX still dead
therefore reset chipRecoveryFailures, so a chip that could be re-inited forever
while never receiving again held the ladder at zero and never reached the
reboot. The other drivers had the same hole from the other side: the caller's
retry startReceive() runs after the reset, so a retry that failed again left the
count cleared.
RadioLibInterface::startReceive() is now the only place the ladder clears, and
it only runs once the chip actually accepted RX. The threshold is judged at the
top of the next attempt - a throttle window later, after that attempt's retry
(the caller's, or fullBegin's own) has had its chance to clear it. That also
drops the old false positive where the reboot was armed before the retry that
would have succeeded.
RF95Interface::startReceive() set isReceiving directly instead of calling the
base, so on RF95 nothing ever cleared rxOffline or the ladder: the first failed
RX start left periodicRadioMaintenance() re-initing forever, and with the count
now advancing it would have rebooted a working radio.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
---------
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
* fix(lr11x0): recover a chip that lost its state instead of assert-crashing in reconfigure()
* fix(radio): extend chip-state-loss recovery to SX126x, SX128x, RF95, and LR20x0
* fix(lora): skip DIO detach when no ISR is attached
Fixes#11371
* fix(lora): latch the ISR-armed flag instead of tracking attach state
The flag is now written once from task context and only read from ISR context.
* add noise floor
* Sliding window noise floor
* Add getCurrentRSSI() to SimRadio for noise floor support
* Remove sendLocalStatsToPhone call from runOnce
* Change noise floor to int32_t type
* Use int32_t for RSSI sample storage in noise floor
* Remove float cast from noise floor assignment
* Fix Copilot review issues: fix noise floor logic, types, and null pointer
- Use robust busyTx/busyRx checks instead of simple isReceiving check
- Initialize noiseFloorSamples to NOISE_FLOOR_MIN instead of 0
- Move noise_floor assignment inside null check to prevent potential crash
- Change getNoiseFloor() and getAverageNoiseFloor() to return int32_t
- Fix RSSI validation to check for positive values (rssi > 0)
- Fix format specifier from %.1f to %d for int32_t
- Update comments to accurately reflect the sampling logic
* Fix RSSI condition to include zero value
* Change noise floor initialization to zero
* Disable noise floor for LR11x0 chips: getRSSI(bool) unsupported
* Remove updateNoiseFloor call from onNotify to avoid radio queue overflow
Per PR review feedback, calling updateNoiseFloor() in onNotify() for every
ISR event (ISR_TX, ISR_RX, TRANSMIT_DELAY_COMPLETED) can cause the LoRa
radio queue to get full. The noise floor sampling still happens in
startReceive() and after transmitting.
* fix lr11x0 current rssi
* Address noise floor review comments
* Address Copilot SimRadio noise floor comments
* Fix RadioLibInterface formatting
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Add powerlimits to reconfigured radio settings as well as init settings.
* Refactor preamble length handling for wide LoRa configurations
* Moved the preamble setting to the main class and made the references static
Using long interleaving is not a breaking change, the receiver node is able
to use the lora header to know if LI encoding is used or not and will
decode LI packets correctly.
However the problem is SX127x and other first generation LoRa IP which do not
support LI at all, for theses it is a breaking change.
HOWEVER due to the sync word bug the LR11x0 already can't talk with SX127x,
so if we enable LI on theses no one would be able to tell.
Same for SX128x altho this is because it works on 2.4Ghz which is incompatible with SX127x.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* Log and save in config lora tx_power after limits applyng
* Log and save in config lora tx_power after limits applyng
* Trunk fmt
* Remove duplicate logic
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
- Rename REGULATORY_GAIN_LORA to TX_GAIN_LORA
- Move gain-based Tx power clamping from RadioInterface::applyModemConfig() to RadioInterface::limitPower()
- User-configured Tx power now matches the Tx power out of the device connector
- Re-order [LoRa Chip]Interface.cpp limitPower() to take place before the final Tx power clamping so we clamp based on the pre-PA Tx power rather than user-configured Tx power
Tested on XIAO BLE variant.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* 2.6 protos
* [create-pull-request] automated change (#5789)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Hello world support for UDP broadcasts over the LAN on ESP32 (#5779)
* UDP local area network meshing on ESP32
* Logs
* Comment
* Update UdpMulticastThread.h
* Changes
* Only use router->send
* Make NodeDatabase (and file) independent of DeviceState (#5813)
* Make NodeDatabase (and file) independent of DeviceState
* 70
* Remove logging statement no longer needed
* Explicitly set CAD symbols, improve slot time calculation and adjust CW size accordingly (#5772)
* File system persistence fixes
* [create-pull-request] automated change (#6000)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Update ref
* Back to 80
* [create-pull-request] automated change (#6002)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* 2.6 <- Next hop router (#6005)
* Initial version of NextHopRouter
* Set original hop limit in header flags
* Short-circuit to FloodingRouter for broadcasts
* If packet traveled 1 hop, set `relay_node` as `next_hop` for the original transmitter
* Set last byte to 0xFF if it ended at 0x00
As per an idea of @S5NC
* Also update next-hop based on received DM for us
* temp
* Add 1 retransmission for intermediate hops when using NextHopRouter
* Add next_hop and relayed_by in PacketHistory for setting next-hop and handle flooding fallback
* Update protos, store multiple relayers
* Remove next-hop update logic from NeighborInfoModule
* Fix retransmissions
* Improve ACKs for repeated packets and responses
* Stop retransmission even if there's not relay node
* Revert perhapsRebroadcast()
* Remove relayer if we cancel a transmission
* Better checking for fallback to flooding
* Fix newlines in traceroute print logs
* Stop retransmission for original packet
* Use relayID
* Also when want_ack is set, we should try to retransmit
* Fix cppcheck error
* Fix 'router' not in scope error
* Fix another cppcheck error
* Check for hop_limit and also update next hop when `hop_start == hop_limit` on ACK
Also check for broadcast in `getNextHop()`
* Formatting and correct NUM_RETRANSMISSIONS
* Update protos
* Start retransmissions in NextHopRouter if ReliableRouter didn't do it
* Handle repeated/fallback to flooding packets properly
First check if it's not still in the TxQueue
* Guard against clients setting `next_hop`/`relay_node`
* Don't cancel relay if we were the assigned next-hop
* Replies (e.g. tapback emoji) are also a valid confirmation of receipt
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
* fix "native" compiler errors/warnings NodeDB.h
* fancy T-Deck / SenseCAP Indicator / unPhone / PICOmputer-S3 TFT screen (#3259)
* lib update: light theme
* fix merge issue
* lib update: home buttons + button try-fix
* lib update: icon color fix
* lib update: fix instability/crash on notification
* update lib: timezone
* timezone label
* lib update: fix set owner
* fix spiLock in RadioLibInterface
* add picomputer tft build
* picomputer build
* fix compiler error std::find()
* fix merge
* lib update: theme runtime config
* lib update: packet logger + T-Deck Plus
* lib update: mesh detector
* lib update: fix brightness & trackball crash
* try-fix less paranoia
* sensecap indicator updates
* lib update: indicator fix
* lib update: statistic & some fixes
* lib-update: other T-Deck touch driver
* use custom touch driver for Indicator
* lower tft task prio
* prepare LVGL ST7789 driver
* lib update: try-fix audio
* Drop received packets from self
* Additional decoded packet ignores
* Honor flip & color for Heltec T114 and T190 (#4786)
* Honor TFT_MESH color if defined for Heltec T114 or T190
* Temporary: point lib_deps at fork of Heltec's ST7789 library
For demo only, until ST7789 is merged
* Update lib_deps; tidy preprocessor logic
* Download debian files after firmware zip
* set title for protobufs bump PR (#4792)
* set title for version bump PR (#4791)
* Enable Dependabot
* chore: trunk fmt
* fix dependabot syntax (#4795)
* fix dependabot syntax
* Update dependabot.yml
* Update dependabot.yml
* Bump peter-evans/create-pull-request from 6 to 7 in /.github/workflows (#4797)
* Bump docker/build-push-action from 5 to 6 in /.github/workflows (#4800)
* Actions: Semgrep Images have moved from returntocorp to semgrep (#4774)
https://hub.docker.com/r/returntocorp/semgrep notes: "We've moved!
Official Docker images for Semgrep now available at semgrep/semgrep."
Patch updates our CI workflow for these images.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Bump meshtestic from `31ee3d9` to `37245b3` (#4799)
Bumps [meshtestic](https://github.com/meshtastic/meshTestic) from `31ee3d9` to `37245b3`.
- [Commits](https://github.com/meshtastic/meshTestic/compare/31ee3d90c8bef61e835c3271be2c7cda8c4a5cc2...37245b3d612a9272f546bbb092837bafdad46bc2)
---
updated-dependencies:
- dependency-name: meshtestic
dependency-type: direct:production
...
Signed-off-by: dependabot[bot] <support@github.com>
Co-authored-by: dependabot[bot] <49699333+dependabot[bot]@users.noreply.github.com>
* [create-pull-request] automated change (#4789)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Bump pnpm/action-setup from 2 to 4 in /.github/workflows (#4798)
Bumps [pnpm/action-setup](https://github.com/pnpm/action-setup) from 2 to 4.
- [Release notes](https://github.com/pnpm/action-setup/releases)
- [Commits](https://github.com/pnpm/action-setup/compare/v2...v4)
---
updated-dependencies:
- dependency-name: pnpm/action-setup
dependency-type: direct:production
update-type: version-update:semver-major
...
Signed-off-by: dependabot[bot] <support@github.com>
Co-authored-by: dependabot[bot] <49699333+dependabot[bot]@users.noreply.github.com>
* Raspberry Pico2 - needs protos
* Re-order doDeepSleep (#4802)
Make sure PMU sleep takes place before I2C ends
* [create-pull-request] automated change
* heltec-wireless-bridge
requires Proto PR first
* feat: trigger class update when protobufs are changed
* meshtastic/ is a test suite; protobufs/ contains protobufs;
* Update platform-native to pick up portduino crash fix (#4807)
* Hopefully extract and commit to meshtastic.github.io
* CI fixes
* [Board] DIY "t-energy-s3_e22" (#4782)
* New variant "t-energy-s3_e22"
- Lilygo T-Energy-S3
- NanoVHF "Mesh-v1.06-TTGO-T18" board
- Ebyte E22 Series
* add board_level = extra
* Update variant.h
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Consolidate variant build steps (#4806)
* poc: consolidate variant build steps
* use build-variant action
* only checkout once and clean up after run
* Revert "Consolidate variant build steps (#4806)" (#4816)
This reverts commit 9f8d86cb25.
* Make Ublox code more readable (#4727)
* Simplify Ublox code
Ublox comes in a myriad of versions and settings. Presently our
configuration code does a lot of branching based on versions being
or not being present.
This patch adds version detection earlier in the piece and branches
on the set gnssModel instead to create separate setup methods for Ublox 6,
Ublox 7/8/9, and Ublox10.
Additionally, adds a macro to make the code much shorter and more
readable.
* Make trunk happy
* Make trunk happy
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Consider the LoRa header when checking packet length
* Minor fix (#4666)
* Minor fixes
It turns out setting a map value with the index notation causes
an lookup that can be avoided with emplace. Apply this to one line in
the StoreForward module.
Fix also Cppcheck-determined highly minor performance increase by
passing gpiochipname as a const reference :)
The amount of cycles used on this laptop while learning about these
callouts from cppcheck is unlikely to ever be more than the cycles
saved by the fixes ;)
* Update PortduinoGlue.cpp
* Revert "Update classes on protobufs update" (#4824)
* Revert "Update classes on protobufs update"
* remove quotes to fix trunk.
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Implement optional second I2C bus for NRF52840
Enabled at compile-time if WIRE_INFERFACES_COUNT defined as 2
* Add I2C bus to Heltec T114 header pins
SDA: P0.13
SCL: P0.16
Uses bus 1, leaving bus 0 routed to the unpopulated footprint for the RTC (general future-proofing)
* Tidier macros
* Swap SDA and SCL
SDA=P0.16, SCL=P0.13
* Refactor and consolidate time window logic (#4826)
* Refactor and consolidate windowing logic
* Trunk
* Fixes
* More
* Fix braces and remove unused now variables.
There was a brace in src/mesh/RadioLibInterface.cpp that was breaking
compile on some architectures.
Additionally, there were some brace errors in
src/modules/Telemetry/AirQualityTelemetry.cpp
src/modules/Telemetry/EnvironmentTelemetry.cpp
src/mesh/wifi/WiFiAPClient.cpp
Move throttle include in WifiAPClient.cpp to top.
Add Default.h to sleep.cpp
rest of files just remove unused now variables.
* Remove a couple more meows
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Rename message length headers and set payload max to 255 (#4827)
* Rename message length headers and set payload max to 255
* Add MESHTASTIC_PKC_OVERHEAD
* compare to MESHTASTIC_HEADER_LENGTH
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* Check for null before printing debug (#4835)
* fix merge
* try-fix crash
* lib update: fix neighbors
* fix GPIO0 mode after I2S audio
* lib update: audio fix
* lib update: fixes and improvements
* extra
* added ILI9342 (from master)
* device-ui persistency
* review update
* fix request, add handled
* fix merge issue
* fix merge issue
* remove newline
* remove newlines from debug log
* playing with locks; but needs more testing
* diy mesh-tab initial files
* board definition for mesh-tab (not yet used)
* use DISPLAY_SET_RESOLUTION to avoid hw dependency in code
* no telemetry for Indicator
* 16MB partition for Indicator
* 8MB partition for Indicator
* stability: add SPI lock before saving via littleFS
* dummy for config transfer (#5154)
* update indicator (due to compile and linker errors)
* remove faulty partition line
* fix missing include
* update indicator board
* update mesh-tab ILI9143 TFT
* fix naming
* mesh-tab targets
* try: disable duplicate locks
* fix nodeDB erase loop when free mem returns invalid value (0, -1).
* upgrade toolchain for nrf52 to gcc 9.3.1
* try-fix (workaround) T-Deck audio crash
* update mesh-tab tft configs
* set T-Deck audio to unused 48 (mem mclk)
* swap mclk to gpio 21
* update meshtab voltage divider
* update mesh-tab ini
* Fixed the issue that indicator device uploads via rp2040 serial port in some cases.
* Fixed the issue that the touch I2C address definition was not effective.
* Fixed the issue that the wifi configuration saved to RAM did not take effect.
* rotation fix; added ST7789 3.2" display
* dreamcatcher: assign GPIO44 to audio mclk
* mesh-tab touch updates
* add mesh-tab powersave as default
* fix DIO1 wakeup
* mesh-tab: enable alert message menu
* Streamline board definitions for first tech preview. (#5390)
* Streamline board definitions for first tech preview. TBD: Indicator Support
* add point-of-checkin
* use board/unphone.json
---------
Co-authored-by: mverch67 <manuel.verch@gmx.de>
* fix native targets
* add RadioLib debugging options for (T-Deck)
* fix T-Deck build
* fix native tft targets for rpi
* remove wrong debug defines
* t-deck-tft button is handled in device-ui
* disable default lightsleep for indicator
* Windows Support - Trunk and Platformio (#5397)
* Add support for GPG
* Add usb device support
* Add trunk.io to devcontainer
* Trunk things
* trunk fmt
* formatting
* fix trivy/DS002, checkov/CKV_DOCKER_3
* hide docker extension popup
* fix trivy/DS026, checkov/CKV_DOCKER_2
* fix radioLib warnings for T-Deck target
* wake screen with button only
* use custom touch driver
* define wake button for unphone
* use board definition for mesh-tab
* mesh-tab rotation upside-down
* update platform native
* use MESH_TAB hardware model definition
* radioLib update (fix crash/assert)
* reference seeed indicator fix commit arduino-esp32
* Remove unneeded file change :)
* disable serial module and tcp socket api for standalone devices (#5591)
* disable serial module and tcp socket api for standalone devices
* just disable webserver, leave wifi available
* disable socket api
* mesh-tab: lower I2C touch frequency
* log error when packet queue is full
* add more locking for shared SPI devices (#5595)
* add more locking for shared SPI devices
* call initSPI before the lock is used
* remove old one
* don't double lock
* Add missing unlock
* More missing unlocks
* Add locks to SafeFile, remove from `readcb`, introduce some LockGuards
* fix lock in setupSDCard()
* pull radiolib trunk with SPI-CS fixes
* change ContentHandler to Constructor type locks, where applicable
---------
Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
* T-Deck: revert back to lovyanGFX touch driver
* T-Deck: increase allocated PSRAM by 50%
* mesh-tab: streamline target definitions
* update RadioLib 7.1.2
* mesh-tab: fix touch rotation 4.0 inch display
* Mesh-Tab platformio: 4.0inch: increase SPI frequency to max
* mesh-tab: fix rotation for 3.5 IPS capacitive display
* mesh-tab: fix rotation for 3.2 IPS capacitive display
* restructure device-ui library into sub-directories
* preparations for generic DisplayDriverFactory
* T-Deck: increase LVGL memory size
* update lib
* trunk fmt
---------
Signed-off-by: dependabot[bot] <support@github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: Jason Murray <15822260+scruplelesswizard@users.noreply.github.com>
Co-authored-by: Jason Murray <jason@chaosaffe.io>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: dependabot[bot] <49699333+dependabot[bot]@users.noreply.github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: virgil <virgil.wang.cj@gmail.com>
Co-authored-by: Mark Trevor Birss <markbirss@gmail.com>
Co-authored-by: Kalle Lilja <15094562+ThatKalle@users.noreply.github.com>
Co-authored-by: GUVWAF <thijs@havinga.eu>
* Version this
* Update platformio.ini (#6006)
* tested higher speed and it works
* Un-extra
* Add -tft environments to the ci matrix
* Exclude unphone tft for now. Something is wonky
* fixed Indicator touch issue (causing IO expander issues), added more RAM
* update lib
* fixed Indicator touch issue (causing IO expander issues), added more RAM (#6013)
* increase T-Deck PSRAM to avoid too early out-of-memory when messages fill up the storage
* update device-ui lib
* Fix T-Deck SD card detection (#6023)
* increase T-Deck PSRAM to avoid too early out-of-memory when messages fill up the storage
* fix SDCard for T-Deck; allow SPI frequency config
* meshtasticd: Add X11 480x480 preset (#6020)
* Littlefs per device
* 2.6 update
* [create-pull-request] automated change (#6037)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* InkHUD UI for E-Ink (#6034)
* Decouple ButtonThread from sleep.cpp
Reorganize sleep observables. Don't call ButtonThread methods inside doLightSleep. Instead, handle in class with new lightsleep Observables.
* InkHUD: initial commit (WIP)
Publicly discloses the current work in progress. Not ready for use.
* feat: battery icon
* chore: implement meshtastic/firmware #5454
Clean up some inline functions
* feat: menu & settings for "jump to applet"
* Remove the beforeRender pattern
It hugely complicates things. If we can achieve acceptable performance without it, so much the better.
* Remove previous Map Applet
Needs re-implementation to work without the beforeRender pattern
* refactor: reimplement map applet
Doesn't require own position
Doesn't require the beforeRender pattern to precalculate; now all-at-once in render
Lays groundwork for fixed-size map with custom background image
* feat: autoshow
Allow user to select which applets (if any) should be automatically brought to foreground when they have new data to display
* refactor: tidy-up applet constructors
misc. jobs including:
- consistent naming
- move initializer-list-only constructors to header
- give derived applets unique identifiers for MeshModule and OSThread logging
* hotfix: autoshow always uses FAST update
In future, it *will* often use FAST, but this will be controlled by a WindowManager component which has not yet been written.
Hotfixed, in case anybody is attempting to use this development version on their deployed devices.
* refactor: bringToForeground no longer requests FAST update
In situations where an applet has moved to foreground because of user input, requestUpdate can be manually called, to upgrade to FAST refresh.
More permanent solution for #23e1dfc
* refactor: extract string storage from ThreadedMessageApplet
Separates the code responsible for storing the limited message history, which was previously part of the ThreadedMessageApplet.
We're now also using this code to store the "most recent message". Previously, this was stored in the `InkHUD::settings` struct, which was much less space-efficient.
We're also now storing the latest DM, laying the foundation for an applet to display only DMs, which will complement the threaded message applet.
* fix: text wrapping
Attempts to fix a disparity between `Applet::printWrapped` and `Applet::getWrappedTextHeight`, which would occasionally cause a ThreadedMessageApplet message to render "too short", overlapping other text.
* fix: purge old constructor
This one slipped through the last commit..
* feat: DM Applet
Useful in combination with the ThreadedMessageApplets, which don't show DMs
* fix: applets shouldn't handle events while deactivated
Only one or two applets were actually doing this, but I'm making a habit of having all applets return early from their event handling methods (as good practice), even if those methods are disabled elsewhere (e.g. not observing observable, return false from wantPacket)
* refactor: allow requesting update without requesting autoshow
Some applets may want to redraw, if they are displayed, but not feel the information is worth being brought to foreground for. Example: ActiveNodesApplet, when purging old nodes from list.
* feat: custom "Recently Active" duration
Allows users to tailor how long nodes will appear in the "Recents" applets, to suit the activity level of their mesh.
* refactor: rename some applets
* fix: autoshow
* fix: getWrappedTextHeight
Remove the "simulate" option from printWrapped; too hard to keep inline with genuine printing (because of AdafruitGFX Fonts' xAdvance, mabye?). Instead of simulating, we printWrapped as normal, and discard pixel output by setting crop. Both methods are similarly inefficient, apparently.
* fix: text wrapping in ThreadedMessageApplet
Wrong arguments were passed to Applet::printWrapped
* feat: notifications for text messages
Only shown if current applet does not already display the same info. Autoshow takes priority over notifications, if both would be used to display the same info.
* feat: optimize FAST vs FULL updates
New UpdateMediator class counts the number of each update type, and suggets which one to use, if the code doesn't already have an explicit prefence. Also performs "maintenance refreshes" unprovoked if display is not given an opportunity to before a FULL refresh through organic use.
* chore: update todo list
* fix: rare lock-up of buttons
* refactor: backlight
Replaces the initial proof-of-concept frontlight code for T-Echo
Presses less than 5 seconds momentarily illuminate the display
Presses longer than 5 seconds latch the light, requiring another tap to disable
If user has previously removed the T-Echo's capacitive touch button (some DIY projects), the light is controlled by the on-screen menu. This fallback is used by all T-Echo devices, until a press of the capacitive touch button is detected.
* feat: change tile with aux button
Applied to VM-E290.
Working as is, but a refactor of WindowManager::render is expected shortly, which will also tidy code from this push.
* fix: specify out-of-the-box tile assignments
Prevents placeholder applet showing on initial boot, for devices which use a mult-tile layout by default (VM-E290)
* fix: verify settings version when loading
* fix: wrong settings version
* refactor: remove unimplemented argument from requestUpdate
Specified whether or not to update "async", however the implementation was slightly broken, Applet::requestUpdate is only handled next time WindowManager::runOnce is called. This didn't allow code to actually await an update, which was misleading.
* refactor: renaming
Applet::render becomes Applet::onRender.
Tile::displayedApplet becomes Tile::assignedApplet.
New onRender method name allows us to move some of the pre and post render code from WindowManager into new Applet::render method, which will call onRender for us.
* refactor: rendering
Bit of a tidy-up. No intended change in behavior.
* fix: optimize refresh times
Shorter wait between retrying update if display was previously busy.
Set anticipated update durations closer to observed values. No signifacant performance increase, but does decrease the amount of polling required.
* feat: blocking update for E-Ink
Option to wait for display update to complete before proceeding. Important when shutting down the device.
* refactor: allow system applets to lock rendering
Temporarily prevents other applets from rendering.
* feat: boot and shutdown screens
* feat: BluetoothStatus
Adds a meshtastic::Status object which exposes the state of the Bluetooth connection. Intends to allow decoupling of UI code.
* feat: Bluetooth pairing screen
* fix: InkHUD defaults not honored
* fix: random Bluetooth pin for NicheGraphics UIs
* chore: button interrupts tested
* fix: emoji reactions show as blank messages
* fix: autoshow and notification triggered by outgoing message
* feat: save InkHUD data before reboot
Implemented with a new Observable. Previously, config and a few recent messages were saved on shutdown. These were lost if the device rebooted, for example when firmware settings were changed by a client. Now, the InkHUD config and recent messages saved on reboot, the same as during an intentional shutdown.
* feat: imperial distances
Controlled by the config.display.units setting
* fix: hide features which are not yet implemented
* refactor: faster rendering
Previously, only tiles which requested update were re-rendered. Affected tiles had their region blanked before render, pixel by pixel. Benchmarking revealed that it is significantly faster to memset the framebuffer and redraw all tiles.
* refactor: tile ownership
Tiles and Applets now maintain a reciprocal link, which is enforced by asserts. Less confusing than the old situation, where an applet and a tile may disagree on their relationship. Empty tiles are now identified by a nullptr *Applet, instead of by having the placeholderApplet assigned.
* fix: notifications and battery when menu open
Do render notifications in front of menu; don't render battery icon in front of menu.
* fix: simpler defaults
Don't expose new users to multiplexed applets straight away: make them enable the feature for themselves.
* fix: Inputs::TwoButton interrupts, when only one button in use
* fix: ensure display update is complete when ESP32 enters light sleep
Many panels power down automatically, but some require active intervention from us. If light sleep (ESP32) occurs during a display update, these panels could potentially remain powered on, applying voltage the pixels for an extended period of time, and potentially damaging the display.
* fix: honor per-variant user tile limit
Set as the default value for InkHUD::settings.userTiles.maxCount in nicheGraphics.h
* feat: initial InkHUD support for Wireless Paper v1.1 and VM-E213
* refactor: Heard and Recents Applets
Tidier code, significant speed boost. Possibly no noticable change in responsiveness, but rendering now spends much less time blocking execution, which is important for correction functioning of the other firmware components.
* refactor: use a common pio base config
Easier to make any future PlatformIO config changes
* feat: tips
Show information that we think the user might find helpful. Some info shown first boot only. Other info shown when / if relevant.
* fix: text wrapping for '\n'
Previously, the newline was honored, but the adojining word was not printed.
* Decouple ButtonThread from sleep.cpp
Reorganize sleep observables. Don't call ButtonThread methods inside doLightSleep. Instead, handle in class with new lightsleep Observables.
* feat: BluetoothStatus
Adds a meshtastic::Status object which exposes the state of the Bluetooth connection. Intends to allow decoupling of UI code.
* feat: observable for reboot
* refactor: Heltec VM-E290 installDefaultConfig
* fix: random Bluetooth pin for NicheGraphics UIs
* update device-ui: fix touch/crash issue while light sleep
* Collect inkhud
* fix: InkHUD shouldn't nag about timezone (#6040)
* Guard eink drivers w/ MESHTASTIC_INCLUDE_NICHE_GRAPHICS
* Case sensitive perhaps?
* More case-sensitivity instances
* Moar
* RTC
* Yet another case issue!
* Sigh...
* MUI: BT programming mode (#6046)
* allow BT connection with disabled MUI
* Update device-ui
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* MUI: fix nag timeout, disable BT programming mode for native (#6052)
* allow BT connection with disabled MUI
* Update device-ui
* MUI: fix nag timeout default and remove programming mode for native
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* remove debuglog leftover
* Wireless Paper: remove stray board_level = extra (#6060)
Makes sure the InkHUD version gets build into the release zip
* Fixed persistence stragglers from NodeDB / Device State divorce (#6059)
* Increase `MAX_THREADS` for InkHUD variants with WiFi (#6064)
* Licensed usage compliance (#6047)
* Prevent psk and legacy admin channel on licensed mode
* Move it
* Consolidate warning strings
* More holes
* Device UI submodule bump
* Prevent licensed users from rebroadcasting unlicensed traffic (#6068)
* Prevent licensed users from rebroadcasting unlicensed traffic
* Added method and enum to make user license status more clear
* MUI: move UI initialization out of main.cpp and adding lightsleep observer + mutex (#6078)
* added device-ui to lightSleep observers for handling graceful sleep; refactoring main.cpp
* bump lib version
* Update device-ui
* unPhone TFT: include into build, enable SD card, increase PSRAM (#6082)
* unPhone-tft: include into build, enable SD card, increase assigned PSRAM
* lib update
* Backup / migrate pub private keys when upgrading to new files in 2.6 (#6096)
* Save a backup of pub/private keys before factory reset
* Fix licensed mode warning
* Unlock spi on else file doesn't exist
* Update device-ui
* Update protos and device-ui
* [create-pull-request] automated change (#6129)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Proto
* [create-pull-request] automated change (#6131)
* Proto update for backup
* [create-pull-request] automated change (#6133)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Update protobufs
* Space
* [create-pull-request] automated change (#6144)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Protos
* [create-pull-request] automated change (#6152)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Updeet
* device-ui lib update
* fix channel OK button
* device-lib update: fix settings panel -> no scrolling
* device-ui lib: last minute update
* defined(SENSECAP_INDICATOR)
* MUI hot-fix pub/priv keys
* MUI hot-fix username dialog
* MUI: BT programming mode button
* Update protobufs
---------
Signed-off-by: dependabot[bot] <support@github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: Jason Murray <15822260+scruplelesswizard@users.noreply.github.com>
Co-authored-by: Jason Murray <jason@chaosaffe.io>
Co-authored-by: dependabot[bot] <49699333+dependabot[bot]@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: virgil <virgil.wang.cj@gmail.com>
Co-authored-by: Mark Trevor Birss <markbirss@gmail.com>
Co-authored-by: Kalle Lilja <15094562+ThatKalle@users.noreply.github.com>
Co-authored-by: rcarteraz <robert.l.carter2@gmail.com>
* For each GPIO PIN, allow to specify gpiochip and line
* Added support for LLCC68 in native env.
* Removed one if by employing &&
* Fix for log, as std::string and not const char*
* Remove CH341 flag, enabling it for all LoRa chips
* Provide a default example
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Refactor and consolidate windowing logic
* Trunk
* Fixes
* More
* Fix braces and remove unused now variables.
There was a brace in src/mesh/RadioLibInterface.cpp that was breaking
compile on some architectures.
Additionally, there were some brace errors in
src/modules/Telemetry/AirQualityTelemetry.cpp
src/modules/Telemetry/EnvironmentTelemetry.cpp
src/mesh/wifi/WiFiAPClient.cpp
Move throttle include in WifiAPClient.cpp to top.
Add Default.h to sleep.cpp
rest of files just remove unused now variables.
* Remove a couple more meows
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* fix linter warning
* Add MaxNodes to Native
* It compiles...
* Convert nodedb to use new
* Closer but still broken.
* Finally working
* Remove unintended lines
* Don't include a pointer
* Capitalization matters.
* avoid rename in protocol regen
* When trimming the nodeDB, start with a cleanup
* Remove extra cleanupMeshDB() call for now
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Move to Portduino's getMacAddr()
* Add ST7735/S screen support
* Push Raspbian support into native target
* Remove latent pigpio references.
* CardKB defensive programming
* Adds configurable spidev
* Fixes to build on Fedora 40
* ENUMs are not #defines. Pull latest portduino
* Add more configuration options for SPI displays
* Add config.yaml option to set DIO3_TCXO_VOLTAGE
* change tft clear() to fillScreen()
Maintains compatability with ESPI driver.
* Adds TXen and RXen pins to portduino
* Add -c --config options to specify config file
* Fail when a specified config file is unavailable
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Use startReceive() instead of startReceiveDutyCycleAuto()
* Add preamble detected IRQ
* Escape from 'freeze' state when packet should have been received
* Use RADIOLIB_GODMODE for access to clearIrqStatus
* SX126x: Better handling of false preamble detections
* SX128x: Add preamble IRQ and false detection handling to active receiving check
* Remove unnecessary function declaration
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add HEADER_VALID IRQ flag for SX126x/8x to detect actively receiving
Needs new RadioLib commit
* Update comments
* Use latest RadioLib release
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Ben Meadors