minor: Fix some unwanted chars in input files

conf/energy_count_3000.conf

@@ -1,8 +1,8 @@
 # EC3k Energy Count Control
 #
 # "Voltcraft Energy Count 3000" (868.3 MHz) sensor sold by Conrad
-# aka “Velleman NETBSEM4”
-# aka “La Crosse Technology Remote Cost Control Monitor – RS3620”.
+# aka "Velleman NETBSEM4"
+# aka "La Crosse Technology Remote Cost Control Monitor – RS3620".
 # aka "ELV Cost Control"
 #
 # Stub driver

src/devices/acurite_01185m.c

@@ -27,7 +27,7 @@ Modulation:
 S.a. #1824
 
 Temperature is 16 bit, degrees F, scaled x10 +900.
-The first reading is the “Meat” channel and the second is for the “Ambient” or grill temperature.
+The first reading is the "Meat" channel and the second is for the "Ambient" or grill temperature.
 The range would be around -57F to 572F with the manual stating temps higher than 700F could damage the sensor.
 
 - A value of 0x1b58 (7000 / 610F) indicates the sensor is unplugged and sending an E1 error to the displays.

src/devices/emontx.c

@@ -33,7 +33,7 @@ http://jeelabs.org/2011/06/09/rf12-packet-format-and-design/
 The RFM69 chip misses out the zero bit at the end of the
 0xAA 0xAA 0xAA preamble; the receivers only use it to set
 up the bit timing, and they look for the 0x2D at the start
-of the packet. So we'll do the same — except since we're
+of the packet. So we'll do the same -- except since we're
 specifically looking for emonTx packets, we can require a
 little bit more. We look for a group of 0xD2, and we
 expect the CDA bits in the header to all be zero:

src/devices/geo_minim.c

@@ -31,11 +31,11 @@ or as follows:
 
 1. On the display, hold down the <- and +> buttons together for 3 seconds.
 2. At the next screen, hold down the middle button for 3 seconds until the
-   display shows “Pair?”
+   display shows "Pair?"
 3. On the sensor, press and hold the pair button (next to the red light)
    until the red LED light illuminates.
 4. Release the pair button and the LED flashes as the transmitter pairs.
-5. The display should now read “Paired CT"
+5. The display should now read "Paired CT"
 
 When paired the display listens for sensor packets and then transmits a
 summary packet using the same protocol.

src/devices/proove.c

@@ -29,7 +29,7 @@ Proove packet structure (32 bits or 36 bits with dimmer value):
 
     HHHH HHHH HHHH HHHH HHHH HHHH HHGO CCEE [DDDD]
 
-- H = The first 26 bits are transmitter unique codes, and it is this code that the receiver “learns” to recognize.
+- H = The first 26 bits are transmitter unique codes, and it is this code that the receiver "learns" to recognize.
 - G = Group command. Set to 1 for on, 0 for off.
 - O = On/Off bit. Set to 1 for on, 0 for off.
 - C = Channel bits (inverted).

src/devices/tfa_marbella.c

@@ -13,14 +13,13 @@
 TFA Dostmann Marbella (30.3238.06).
 
 Main display cat no: 3066.01
-
-External links
-
-https://www.tfa-dostmann.de/produkt/funk-poolthermometer-marbella-30-3066/
-https://clientmedia.trade-server.net/1768_tfadost/media/3/52/21352.pdf
+
+External links:
+- https://www.tfa-dostmann.de/produkt/funk-poolthermometer-marbella-30-3066/
+- https://clientmedia.trade-server.net/1768_tfadost/media/3/52/21352.pdf
 
 The Marbella sensor operates at 868MHz frequency band.
-
+
 FSK_PCM with 105 us long high durations
 
 AA 2D D4 68 3F 16 0A 31 9A AA XX